rotorx atom 3d models
5358 3d models found related to rotorx atom.thingiverse
I made this ESC cover for the RX122 RotorX atom micro quadcopter , this will fit on a DYS SN20A and XM10A ESC. Added a center hole and side vents for ventilation also the vents will absorb the air's downdraft to avoid turbulence and for added lift.
thingiverse
This is a frame I designed based loosely on the RotorX Atom V1. This frame is no longer being produced which is a shame as it allowed for much more flexibility for custom builds over the newer V2 and V3 versions. The camera mount and camera are...
thingiverse
Canopy for the RotorX Atom holds a Foxeer Arrow and GoPro Session. Components used in my build: Kiss AIO FC/ESCs Crossfire Micro RX Unify Pro HV w/ dipole antenna Foxeer Arrow V2 Must use 5mm round standoffs, and the two front standoffs need to be...
thingiverse
My RotorX Atom quad is a bit too peppy to be used indoors without being overly careful, so I designed a prop guard so that I could bump into things without stopping the blades or damaging anything. Update 1: I've added some new versions. One without...
thingiverse
This is Rotorx Atom v3 (4mm) armor boot with an integrated soft mount. Use soft material when printing like TPU. I cut supports with wire nippers, but a hobby knife should also do the trick. Two versions, I used the v3.3 version with extra...
thingiverse
This is designed to fit in an atom using a Genix PDB and naze stack. Print Settings Printer: Wanhao i3 Rafts: ...
thingiverse
Rotor X Atom Standoff * Diameter: 6mm Screw Hole: 2.04mm Screw threads will make its way in the plastic. STL in metric units so you can adjust the height, by scaling it in Cura. ...Print Settings Printer Brand: RepRap ...
thingiverse
... with the front standoff screws. We keep the nose guard installed at all times, and snap on the boots when we’ll be racing over concrete or asphalt. I carry many products for the RotorX Atom at http://genixrc.com/product-category/rotorx-atom/
thingiverse
another variation on munsie888's immortal t arm mount to fit my new RotorX atom v4. it fits all the way out at the end of the arm and there is a groove for a zip tie to hold it all together- will upload pictures when I get started on the build. ... ...
thingiverse
... quite finicky to dial in, and fit could easily vary with your machine. You could scale X/Y to change the hole size easily if it is too tight or loose. I carry many products for the RotorX Atom at http://genixrc.com/product-category/rotorx-atom/
thingiverse
I made a cable saver for the RotorX Atom V2 to keep the power cable from being cut by the frame and shorting. I had to widen out the zip tie holes a bit with a small screwdriver. ...Print Settings Printer Brand: LulzBot ...
thingiverse
This is my remix of http://www.thingiverse.com/thing:1369044 to make it fit the RotorX Atom v1 frame. The original mount only had cradle that the camera sat in. I designed a 2 piece mount that also has a barrel that extends forward to protect the...
thingiverse
These are parts to a camera mount for the RotorX Atom V1. This is an adjustable angle camera mount. This replaces the front standoffs and the holes are sized for an M2 tap, spaced to fit the holes on the Atom frame. It fits the normal tiny 600tvl...
thingiverse
A replacement top plate for the Atom V1 frame. ...The frame is no longer available and the top plate does break when you hit enough hard things :)
thingiverse
This mount was designed to be used with the stock Rotor X Atom V2 Camera with the 110 Lens. Other lens's may fit, but cannot guarantee anything. It is designed so that you can screw the lens into place. it can also be cut down the center through...
thingiverse
... go get it more robust. If you wish feel free to print it in one piece. After Print is finished, snap it in your Atom V2 hood and glue it in place. ...To install the hood with antenna protector you have to remove the shrinking tube from the antenna.
prusaprinters
I made this Thing to protect my Whip antenna. v2.0 now the antenna fits with the shrinking tube for more protect to the antenna if the canopy is removed Print instructionsCategory: R/C Vehicles Print Settings Printer: CoreXY Rafts: No Supports: No...
thingiverse
RotorX RX122 Atom Antenna Mount. To be mounted using the forward two standoffs of the fc standoffs. ... Print Settings Rafts: No Supports: ...
thingiverse
RX122 RotorX Atom XAT520 Cam Holder 25° 19.5mm height, leaves enoguh space for the Kiss CC
thingiverse
... atom armor to fit the 4mm thick frame. ... I realized that the updated noseguard didn't match the layout of my V4 atom, so redesigned it- I have printed it and it is a perfect fit. ... just no pictures since it is wrapped up in a christmas present :)
thingiverse
These will now be included in all Atom kits moving forward from RotorX. I am putting the file up here for all to use. Do not use this to sell or make money on, unless you have already contacted Myself, or Alderboy, or another member of the RotorX...
thingiverse
The screws and the Atom V2 canopy hold everything nice and tight even with the slice in the mount. Huge credit to Drew Price (TenFPV) for doing the bulk of the design work on these!!! ...Print Settings Printer: FlashForge...
thingiverse
The original polycarbonate canopy from rotorx is around 9 grams. 1/5/19- added a new version that is based on building my atom. using the hglrc zeus, it covers the rear canopy mounting holes. I was trying to use 3mm standoffs as nuts on the front...
thingiverse
This is designed by Marty of Rotorx!! Must be printed in flexible materials due to the nature of the install. I used Ninjaflex Semi flex with the best results. ...I am also going to upload a modified version with just the front part.
thingiverse
A remix of the Atom Wall. Only the front part including the camera mount. best in Semi- or Flexible material. ...If you were to scale it up a little bit (5%) and have a drill bit to ream out the holes you may be able to get away with regular filament,...
thingiverse
This mount is made for my Atom V1. The cam sits in it in a 40° angle and ist fixiated with double sided tape and a small ziptie. It's 24mm in heigth and the front two standoffs have to be 5mm shorter then rear ones. ...In he front also are 2 5mm M2...
thingiverse
This is a canopy for an Atom frame with an Owl cam mounted at 15deg angle (since the owl has huge fov bigger angle not needed) It uses 20mm standoffs and does not rely on the 30.5 screws used for FC and PDB. I emphasise this because I find it to be...
thingiverse
I almost cut my motor wires with a bent prop on my atom V2 after a crash. To protet the wires from the props I created this light weight guard. It is designed to be made out of TPU or Ninjatek Armadillo or Cheeata filament and simply clips onto the...