samsung galaxy tab mount 3d models
388708 3d models found related to samsung galaxy tab mount.prusaprinters
Designed to mount to a utility shelf. All parts printed @ 2mm w/ 3 perimeters, 15% infill except for the two small hanging posts which, for strength, were printed @ 1.5 w/ 4 perimeters and 40% infill. The ball and nut parts print together. Supports...
thingiverse
This is my version of a Mavic Pro tablet mount, this mount is specifically made for the Samsung Galaxy Tab A7 with a silicone cover on it. No supports, infill is whatever you want, I went with 50% for strength. ... Hardware needed, just one 1/4 x...
thingiverse
... together. The hanging posts are designed to not bottom out so you can adjust for the thickness of your shelf allowing for a snug fit when hanging the mount. Be careful not to over-tighten the threaded bits. Hanging posts are 36.5mm apart. ...
thingiverse
Simple wall mount for Samsung Galaxy Tab 3 (SM-T210) 7 inch, portrait orientation.
thingiverse
A wall mount for the Samsung Galaxy Tab A8, at an angle of 60 degrees, with two accessible screw-holes to attach directly to a wall.
thingiverse
Needed a Wall Mount so created this In two parts (Printed face down with Bed support) For my Samsung Galaxy Tab A8 10.5”
thingiverse
For tablet (Samsung galaxy tab 6) for user interface home assistant. Speaker holes on both sides. ... After completing add some padding in the bottom corners and at the top for a snug fit without damaging the tablet.
thingiverse
This wall mount holder is designed to keep your tablet on a wall for a smart home system.
myminifactory
I needed to mount a tablet on the wall so I can monitor all of my sensors through the OpenHAB application. It will probably work for other tablets of similar size.
thingiverse
Wall mounting for a Samsung Galaxy Tab 2 tablet. The housing has the cut out to allow charging while mounted on the wall. It should be noted that this is designed for a home automation system which does not require access to any of the physical...
thingiverse
Simple wall mount for a Samsung Galaxy Tab A 8''. ...I stuck it to a fridge with double sided adhesive tape.
thingiverse
I printed 4 of these so that I could mount my old Galaxy Tab to my kitchen wall with screws. ...It works really well!
thingiverse
I was given a Galaxy tab as a promotional gift and it was destined to be a part of my home automation (domotica) system so I set out to make a nice wall mount that wasn't too large and allowed me to power it up permanently. This is for the Samsung...
prusaprinters
This is a minimalistic wall mount for the Samsung TAB A8 that prints without support and all the pieces should snap together without any modifications or glue.Everything else should be self-explanatory with help from the images I could not...
thingiverse
Mounting can be done normally with 4 screws. On the upper side, a small hole has been left open with which the tablet can be restarted without taking it out of the box if necessary. ... # Support my work <a...
thingiverse
Hi, This is a WallMount for a Samsung Galaxy Tab A8 (2021) model SM-X200. Five screw are needed. One to close de case and fourto fix the case on the support. I printed it on an Alphawise U20 with supports (see print settings section). The...
thingiverse
I epoxied 4 magnets to the back and used a angled usb c cable going to the left I got them from amazon under this listing Strong Neodymium Disc Magnets (6 Pack) - 2X Stronger, 2X Thicker, Powerful, Small, Round, Rare Earth Magnets - N45...
thingiverse
I Designed this tablet holder for my friend's smart home system. He wanted a holder that will keep the tablet in place and hide the cables. If your bed adhesion is good you can print it without rafts. ...I used rafts because of my low bed adhesion.
thingiverse
Two piece wall mount for Samsung Galaxy Tab A8. ... There is enough clearance for front facing camera and brightness sensor to work.
thingiverse
Couldn't find any full closed wall mount for Samsung Galaxy Tab S2 8", so i created it. Tablet will be used as Smart Home centre for home automation, thermostat controll, and for Google Home. Added holes to speakers and microphone and cut for...
prusaprinters
I designed this wall mount so I cold mount my Galaxy Tab A7 on the wall to display HomeAssistant dashboards. The mount is attached to the wall using double sided nano gel tape which doesn't wreck the walls and is easily removable but super strong.
prusaprinters
First Part for a Samsung Galaxy Tab 3 10.0 wall mount with push unlock- Not Tested Tab 3 10.0 v7 + Tab 3 10.0 Wall Mount V3 or Wall mount v5 or Wall mount v6.stl Tab 3 10.0 v14 + Tab 3 10.0 Cover V4 (+ 2x nuts cover v1) + Wall mount v5 or Wall mount...
cults3d
First Part for a Samsung Galaxy Tab 3 10.0 wall mount with push unlock- Not Tested Tab 3 10.0 v7 + Tab 3 10.0 Wall Mount V3 or Wall mount v5 or Wall mount v6.stl Tab 3 10.0 v14 + Tab 3 10.0 Cover V4 (+ 2x nuts cover v1) + Wall mount v5 or Wall mount...
thingiverse
First Part for a Samsung Galaxy Tab 3 10.0 wall mount with push unlock- Not Tested Tab 3 10.0 v7 + Tab 3 10.0 Wall Mount V3 or Wall mount v5 or Wall mount v6.stl Tab 3 10.0 v14 + Tab 3 10.0 Cover V4 (+ 2x nuts cover v1) + Wall mount v5 or Wall mount...
thingiverse
- Standard Version - Printable on printers with larger printer area > 30 cm - Files: - Standard_Version_Lid.stl - Standard_Version_Wall Body.stl - Standard_Version_Samsung_Galaxy_Tab_A7_SM-T500_Wall_Mount_v19.step - Splitted Version - Printable on...
thingiverse
This is a landscape wall mount for the Samsung Galaxy Tab T580 10.1". It fits for tablet width of 155mm. I printed with a 0.4 nozzle and a layer height of 0.25. Slide in the tablet from left or right. ...Support is requiered
thingiverse
The included dimensions are for an Samsung Galaxy Tab A7 Lite (SM-T220). The lid is held with glued-in magnets (5mm x 1mm). ... There is clearance at the bottom for the charging plug.
thingiverse
This mount is designed to fit a Samsung Galaxy Tab 4 10.1 tablet. The tablet slips in from the right side of the mount with openings at the bottom for access to the home buttons and USB port. The tablet may be secured in the mount with an M6 screw...
prusaprinters
The included dimensions are for an Samsung Galaxy Tab A7 Lite (SM-T220).The lid is held with glued-in magnets (5mm x 1mm).There is clearance at the bottom for the charging plug.Printed in PLA with .2mm layer height.Had problems with warping since it...