samsung t5 rack 3d models
44327 3d models found related to samsung t5 rack.thingiverse
SAMSUNG T5 external drive rack for back mounting on a computer. ... I used some 3m double sided tape to stick it to the computer stand.
thingiverse
Rack support for Samsung T5 SSD. ... Allows easy and convenient access for a Raspberry PI
prusaprinters
Rack support for Samsung T5 SSD.Allows easy and convenient access for a Raspberry PI
thingiverse
This is a retainer for a Samsung T5 USB SSD that attaches directly to https://www.thingiverse.com/thing:4756812. The Samsung SSD slips into the retainer and no additional fixing is required. Print lying flat without supports The caddy increases...
prusaprinters
Samsung T5 SSD wallmount I also made a wallmount for two Samsung T5 https://www.prusaprinters.org/de/prints/42016-samsung-t5-ssd-dual-wallmount
thingiverse
~455mm * 6x 5M nuts * 44x M2.5*12mm (32 for 8 Raspberry and 12 for Samsung T5) * 12x M2 nuts (for Samsung T5 holder) * 1x 12v adapter I used [this](https://www.amazon.de/gp/product/B07MJQ8K4P) * 5x 12v PC 80mm coolers [Arctic F8 Value Pack, ACFAN0...
thingiverse
This is a simple SSD sleeve I made for the Samsung T5. ...Mine fit very snugly inside so maybe increase the size a bit in the slicer.
thingiverse
Made this small carrying case that fits 2 Samsung T5 SSD's. Tried to make it as small as possible. ... The total print time for me was about 8,5 hours.
thingiverse
- - - - - - - - - - - - - - - - - - - - - - - - - - - Simpler und schnell zu Druckender Samsung T5 SSD Halter mit Klick-In Montage. Montage erfolgt mittels Powerstrip oder 2x M3 Schrauben. Der Halter kann in PLA Gedruckt werden und hält die SSD...
myminifactory
This is a holder for 4 Samsung T5 SSDs (i thing T7 might fit too, but are a little longer).Fits perfectly printed with my Makerbot 5th gen.Printed without any supports.If disks slide too easily (probable with better printers), a sticker on the inside...
thingiverse
A Case for the Samsung T5 SSD. ======== You can pause the print (see picture) to insert two nuts (for a 6mm Screw). ... I personally welded a sqare of iron to the head of the screw to be able to insert it into a camera hot shoe (for a Black Magic...
thingiverse
This is a holder for 4 Samsung T5 SSDs (i thing T7 might fit too, but are a little longer). Fits perfectly printed with my Makerbot 5th gen. Printed without any supports. ... If disks slide too easily (probable with better printers), a sticker on the...
thingiverse
This is a Cable Management for the small Samsung SSD T5 & T7 Its made outof two parts, so it does fit the bigger T7 too. It´s made outof TPU. The cable catcher is quite grippy. I like that, so they dont loosen up. However - my friends say that...
thingiverse
Important note: this version is deprecated Mark III here https://www.thingiverse.com/thing:4756812 and here: https://uplab.pro/2020/12/raspberry-pi-server-mark-iii/ MARK II is brand new version of my Raspberry Rack Mount...
thingiverse
The SAMSUNG T5 has blazing fast transfer speeds. https://amzn.to/30GBmZK Had to install a USB-C PCIe card in my aging motherboard but now i am transferring files from my internal SSD to the T5 at 480 MB/s. https://bit.ly/2JyHNsP This is all...
thingiverse
This remix just added 2 screwholes. ... I did some size recalculation so now the T5 goes in smooth without a major gaps. Tx for the original design! ...
thingiverse
Wanted to screw a T5-SSD to a surface with easy removal. No USB-hole added (yet), might add this in the future. I printed mine at 102% in Cura, since it is designed with a very tight fit. ... Rotate the print 180 degrees to be able to print it without...
thingiverse
Remix of a SSD bracket. ...Sandwiched 4 of these together to make a small rack. ...In the photo i could not complete printing because I ran out of filament, but works nonetheless.
thingiverse
Based on https://www.smallrig.com/smallrig-mount-for-samsung-t5-ssd-2245.html Requires - 1/4 Allen Bolt - M5 Allen Bolt - M5 Hex Nut Have Fun!
thingiverse
This is a simple Samsung T5 SSD mount for your iMac. ...It hides the drives behind the display nice and neat.
prusaprinters
Protect your Samsung T5 ssd Print-Orientation: Place the fat side down. Material: TPU (PLA might work but does not absorb impacts as good)
thingiverse
Triple Hub for storing three Samsung T5 SSD's on your desk. Makes them immediately swappable. I recommend labeling each seperate drive. ... Printing tips: - Print with left flat side on the bed - Use just a few supports to bridge the gaps for...
thingiverse
This is a holder for 4 Samsung T5 SSDs (i thing T7 might fit too, but are a little longer). Fits perfectly printed with my Makerbot 5th gen. Printed without any supports. ... If disks slide too easily (probable with better printers), a sticker on the...
thingiverse
I designed and 3d printed this protective case for my friend SSD model :- SAMSUNG SSD T5 SPECIFICATIONS FOR PRINT :- Top and bottom layer thickness :- 2.5mm Shell thickness:- 0.8 mm Infill :- 0 % Material (filament) :- NUMAKER'S PLA+ BLACK FILAMENT...
thingiverse
This is an SSD mount useful for attaching a Samsung T5 SSD to the BMPCC4k/6k. It has a design where it lifts the ssd off camera slightly for hovering over the on switch and function buttons. ... You can print as-is for a normal snug fit, or what I did...