samyang 14mm f2 8 lens 3d models
361842 3d models found related to samyang 14mm f2 8 lens.thingiverse
I wanted to use my cokin/Haida P (84x95mm) filters with my 14mm F2.8. **NOTE**: It will only work with cropped sensors (APS-C and below) as with Full Frame you will encounter major vignetting. If you want to print the honeycomb version, you will...
thingiverse
A filterholder for 150 x 150mm rectangular filters for a Samyang XP 14mm f/2.4 ultra wideangle lens. Easy to print in 3 parts. The filter base "housing" ist bigger than filterholders that you can purchase. But you can add e.g. heating foils to warm...
thingiverse
This is a lens cover for the Sigma 14mm F2.8D HSM Aspherical. Fits quite snuggly on my copy of the lens. ...If you want to check if it will fit your lens, the diameter of the lens itself is 81.6mm across the widest part of the lens hood.
cults3d
Lens cap for Samyang 14mm Ultra Wide-Angle f/2.8 IF ED UMC Lens.
thingiverse
Lens cap for Samyang 14mm Ultra Wide-Angle f/2.8 IF ED UMC Lens.
myminifactory
Lens cap for Samyang 14mm Ultra Wide-Angle f/2.8 IF ED UMC Lens.
thingiverse
Print in ABS, fits snug on the lens.
thingiverse
Samyang 14mm 2.8 EOS no has AF confirmation chip. This ring help to glue chip on this lens and you will get confirmation! ...Print Settings Printer Brand: Ultimaker ...
thingiverse
A filter holder for a samyang 14mm. ...100x100mm filters. Do not work on Full Frame cameras Download: https://cults3d.com/en/3d-model/home/lens-samyang-14mm-double-filter-holder
cults3d
A filter holder for a samyang 14mm. 100x100mm filters. ...Do not work on Full Frame cameras
thingiverse
A filter holder for a samyang 14mm. 100x100mm filters Designed for a friend, i dont know if it works! you will need 2 nuts and a 3mm bolt. ... CHECK OUT my portfolio and leave a like: https://www.behance.net/andreziio6a17 It would help a lot!
thingiverse
This is a two ring adaptor and dovetail plate for a Samyang/Rokinon 135mm F2 lens. The dovetail and rings are joined with M4 bolts and the lens is secured in the rings with two M6 nylon bolts, do not over-tighten the front (large ring) nylon bolt as...
thingiverse
Couldn't find a filter holder that can use 100mm size filter for my Samyang 135mm lens hood. So, I rescaled it from the Corkin design and made the filter holder thicker so that it can latch on the lens hood more steadily. I then made the block size...
thingiverse
Customized version of https://www.thingiverse.com/thing:2168672 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2168672
thingiverse
So I thought it would be a good idea for tripod use, to carry the camera with the lens and put not the whole load on the cameras lens bayonet. The MFT version is supplied with a extending-tube that is needed to bridge the distance of the short DSLR...
thingiverse
Simple mount for square filters (100*150mm) for the Samyang/Walimex/Rokinon 14mm f.2.8 lens. Settings: Resolution: 0.2 mm Infill: 15 % No supports needed Print with round side on the printbed. If fit on the lens is too tight, place the mount...
thingiverse
Lens cap cover for an old Carenar with M42 mount for cameras like Zenit 12XL. The caps are printed with a 0.15mm layer height. The rear cap can be screewed. ... Instructions Best results with 0.15mm...
cults3d
If you need a cap for this dreamy lens (МИР-1В), here is one that fits snugly. I printed mine in PLA black. I also included photos, showing the results with and without important things like ironing or concentric pattern enabled. ...Surely it is just an...
thingiverse
This is a lens hood for Tamron SP 24-70mm F2.8 (EF-mount). ... Unfortunately, it cannot be screwed to the lens the other way around.
myminifactory
This a mount holder for a simple packaging foam diffuser for Zuiko 60mm f2.8 lens. ...You would need something like this diffuser on top of your speedlight flash to soften the...
pinshape
This is a seamless lens gear for canons 24mm f2.8 photo lens. Works with standard 0.8 pitch follow focus systems. tested and confirmed to work on the Tilta nucleus nano, and the Ronin S follow focus motors. ... Only includes STL file : Notes to check...
thingiverse
Therefore, I've designed a hands-off focuser solution that integrates with my [Samyang 135mm Lens Collar](https://www.thingiverse.com/thing:5615266) design. This project has 3 aspects: 1. 3d-printed focuser elements for the gears, motor, and...
thingiverse
The 35mm f2.8 lens found on a Nikon L35AF point and shoot camera is rightly highly regarded as a quality 5 element sonnar lens, and is unusually wide for a fixed lens camera. It is not hard to find a broken model as the early electronics driving...
thingiverse
This project at https://sleeplesslights.com/samyang-135mm-f-2-lens-collar-new-design/ More gadgets and astrophotography stuff at https://sleeplesslights.com Update 2022/12/15 - Added the Source FreeCAD FCStd File to Thing Files Update 2023/01/14 -...
thingiverse
... ...It is a focusable adapter that fit my projector lens (Zeiss IKON TALON 1:2.8 / 85mm, Kindermann, 1:2.8 /90mm, but not any Kodak) with Canon EF mount. ...It was modified from AlexEnglish's "EF Mount Module" (http://www.thingiverse.com/thing:10829)