scroll case 3d models

The t cross section in the Servo locker is a piece of 2.85MM Filiment (PETG in my case). The Servo locker was printed via SLA, but can be done in FFF if done carefully. This needs an SG90 servo, and some assorted M3 hardware too. All should be left...

This does NOT work with the "underwater" version of the FujiFilm Quicksnap (the one in the acrylic plastic case). I did not have to buy a new FujiFilm disposable - many camera shops will gladly give you these camera shells which are typically...

In case anyone is wondering, what the white cables are, in my version I connected LED lighting to them. The components can be found under my designs. ... LED Strip: - Light Bar Ender 2020 Remix v2 (LED - light mount, holder) with locking hook ...

The box is based on the one from Jaxel.&nbsp;Box dividersIn case you print several filament swatches, you might need a solution to remember which spools are empty or bad. For this, use these <a...

In the case of the key rack, settings may be the pre-set quick settings including Standard Quality, no supports, layer height of .2mm, 10% infill, 2 shells, using MakerBot PLA, and an extruder temperature of 215 degrees Celsius. Once you have...

You may need a brim for this part (in which case cutting it off with scissors is the best way to get the brim off without damaging the spring). Assembly Instructions: First, check if the button fits into the cover (with the pins away from the...

In many cases the filenames include suggested print settings, but use common sense (or ask me if you have trouble). The pictures have been ordered in a reasonably sensible order now, with the STL previews being the parts themselves, followed by a...

I like building led lamps, and so i decided to modify a 10w led floodlight to make it like a work light with a stand and all .there are 2 versions of the housing , one with premade holes and one with no hole , in case your lamp has different fixing...

https://www.amazon.com/dp/B08NW9KM6Y?psc=1&ref=ppx_yo2_dt_b_product_details Solar powered (optional): Solar panel 6W (pi zero): https://www.adafruit.com/product/1525 9W (pi 3b+): https://www.adafruit.com/product/2747 Solar inverter:...

In this case, please contact; it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3D-print; this is not a scan version. At the photos you can see the contours of the...

There are various lights from Hella in this series with only minor (if at all) differences and package contentstwo sheet metal screws 3.5x9.5 mm (in the case your light comes without screws)some cables and connectors to make up the inards of the...

In this case, please contact me; it's possible to save files at high values, but this will result in a sharp increase in file size. This is a fully solid-state version for 3D printing; this is not a scan version. At the photos you can see the...

This was a personal project, not necessarily a fully realized community project, but I wanted to share it in case someone wanted to use it as is, or build off of it. I designed a custom lamp for the Arturia MatrixBrute synthesizer that uses an LED...

In those cases, there may be a slight bend in the short Capricorn tube that goes from the extruder to hotend, but that should not negatively affect anything. There are two versions of this mount. One is for the 3-wheel hotend carriage that has been...

Or better still print a piece yourself with adjusted dimensions you want to keep in case you are more worried about the performance but don't mind trying new things since these can indeed change many of issues mentioned above simply make copies...

Perspex isn't an idea surface for films, and you will likely get bubbles forming after a few days, but these can be smoothed out, and haven't reappeared on mine. Once you have the perspex covered and the film trimmed in, assemble the four posts,...

Note that it's almost impossible to print good servo shaft splines with an 0.4 nozzle, and in the end I modified a normal servo arm.I have also included a source file for X-axis motor mounts, although I didn't use them myself - the originals are...

There's even a screw to secure your position in case you can't jot down the measurement right away. I hope these will come in handy for makers everywhere. All three parts are already correctly oriented for printing, with no need for supports! Be...

Make some extras in case you break some while inserting into the coupler.&nbsp;Sizing and tolerance:Model dimensions were adjusted to print at desired size. Your printer may give slightly different results and one part or another may need slight...

Although the design uses the components for extra rigidity, it is more flexible then a metal case.Can be printed on a 20x30cm bed now.Made for Rog Maximus XII Extreme (ATX extended) but other MBs will fit as well.Power supply: EVGA SuperNOVA...

If it is not the case, a small stroke of sandpaper to round off the angles and a little silicone grease should solve the problem Place the body cover. ... To know : With repeated handling, the blades may "crease" and lose their smooth appearance,...

In most cases the machine orders will start counting numbers sequentially after first operation if one already began printing part which now would logically need following number placed inside an area where user defines desired print job position so...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

In case of any question or inquiry about the Herman Miller Aeron Stool model, feel free to contact us anytime. Dimension-wise, the perfect sitting position on this chair is easily adjustable from base, with measurements as 68.51 cm x 68.69 cm x...

In my case I power it from the Raspberry PI I use for octoprint.I'm using https://www.home-assistant.io for my home automation so I also hooked this scale into my Home Assistant as a light (the backlight for the display) and as a sensor (the weight...

So at the time of this writing and the time of my order, it was the time of the corona virus crisis (just in case someone reads this in a couple of years and wonders). Every seller online got flooded witch orders and the delivery companies almost...

I created two parts in case I needed to alter the spacing of the magnets or change to different magnets without having to re-glue it to the fan. The four #8 screws actually support the entire stir plate, with the screw ends resting on the table. A...

However, in many cases it either does not matter or you can easily remap the keys in the game or by using the Xbox Accessories app.The Normal paddles do not have this nuisance, but they require a different way of operation that may be more difficult...

In this case, the points are the nodes of a network, creating a complex web of lines and shapes that give the vase its unique character. This algorithmic approach allows for an almost infinite variety of patterns, making each piece truly...

If that's the case, you'll need a 11mm OD bearing with a 12.5mm flange for the pulley. These uxcell F685ZZ Flanged Ball Bearing 5x11x5mm Shielded Chrome Steel Bearings 2pcs by uxcell should work. You will need 3 bearings if you want to use the v2...