scroll case 3d models

Use a lot of infill too, in my case 80%. No part needs support, but if you want to add some on the rectangular gap on the BLTouch mount, it won't hurt. Everything depends on how well you can print bridges. Assembling tips: First assemble the...

In my case, I have fluctuations of ~6 Kelvin over the bed surface (@ 60°C). Though, this did not influence the printing in any significant way for me yet. Print Settings Rafts: No Supports: No Resolution: 0.2 mm layer height, 0.4 mm nozzle diameter...

Eyelet diameter is 7mm (little over ¼").Obviously not suitable for safety relevant applications.Changelog2022-03-15v3complete redesign with smaller dimensions, shorter screw (M3x8mm) and additional clamp only variant2022-03-10v2easier assembly and...

Normally, a sphere wouldn't be retained within a hemispherical cavity, but not in this case. What makes it possible? You start with the cube in two halves, each side holding half of a ball. Show your audience the inside of the cube and point out how...

I thought it would be a good idea to have a spare in case I stripped out a grub screw tap or something. I ordered the wrong version, and it had been sitting in my parts bin since. After deciding to swap out the hot ends for the V6's I can take...

In both cases, the warrior nearest the center is the victor, creating an even match on the battlefield. As on the East, the West Pediment was preceded by a slightly earlier pedimental group, known as West Pediment 1. Unlike East Pediment 1, West...

I have also provided a model for a piece that is not necessary for the official game - Roof (red) which you can use to block 1st and 2nd level buildings in case you want to play like that (In the original rules you can only block 3rd level...

When you have attached the wires to the short solid core sections soldered onto the washer and nut, assembled the spring and plunger and everything works, glue the 2 halves together applying pressure from a hand clamp ot weights while you wait for...

The HOT2Handle is designed to fit some in-car cupholders but with 4 cups that will not be the case. Make sure you are moving in car safely with your coffee. ...The cupholder is not designed to hold the coffee in a secure position while your car is...

... canopy was extremely close to the front propellers. Nobody wants their props striking the canopy, right? So I made some risers that you can use to put your motors a bit higher by simply screwing them in under the motors (in my case BetaFPV 1404s).

Mini-reels all but disappeared from the market.While mini-reels may not be commercially viable, there is still a use-case for them. The fact that several distributors offer a "re-reeling service" proves that there is still a market for buying smaller...

Personally, I like the Super Long version better, but I've put this here in case people want to try it out. 4th up is Version 4, the Angled Front Grip. I started on this one first, and didn't fully like the feel so moved on to Version 5. I might...

In case you use different bell, some adaptation might be needed.Print instructions:PLA0,2mm or 0,3 mm layer heightMOTOR_MOUNT, DRIVE_WHEEL, DRIVEN_WHEEL and AXLE with 100% infillUse 3 perimeters for stand and headstock.Motor is little bit on the...

You'll want to customize that though and print a whole bunch with different settings to createyour perfect switch. Switch Assembly The switch body just snaps together but I made a video in case you're confused: https://youtu.be/q-7IY5NExhA Don't...

Other parts I used to design this: https://www.thingiverse.com/thing:4779428https://grabcad.com/library/noctua-fan-nf-a4x20-flx-4020-1EDIT 1: In case no one wants a channel for LED strips cuz you don't have LED strips, here you go I added a file that...

This could be avoid if you know, and want, to drive directly the stepper coils.Anything that could generate a square signal (if you use the driver), from a 555 chip, to a microcontroller board (like an Arduino, or in my case the EDU-CIAA board). ####...

In case of this casket, the author used an object that was intended for storage purposes but reduced its size. He also used a different material, namely steel.The clock was inspired by the entire highlander cottage with the horst structure and bonnet...

The github repository for the model (containing the complete OpenSCAD project) can be found at https://github.com/simoninns/PinePhone-Dev-Stand # Overview The case is designed in two parts (the stand and the bracket) which slot together. This also...

The box is ~160x100x50mm. I've included the Fusion 360 file in case you'd like to make some changes. Please post your makes if you decide to print one. Print Settings Printer: Wilson TS Rafts: No Supports: No Resolution: 0.2 layer height, 0.6...

In this case those on the plate have been used.The used drag chain bridge that has been used is the following (buy two...

In all cases, expected output from non-native applications should not be assumed equivalent to results seen within approved systems. GEOMETRY Model construction has entailed collapsing its primary stack to streamline structural integrity and simplify...

In the case of Khafre, he and his sculptors managed to express their vision of kingship visually, and in many ways more succinctly than could be done in words alone.  Who was the intended recipient of this message? Perhaps it was intended for no one,...

I just needed some quick mounting tabs (which I'll include here in case someone wants to go that route) and the smallest BTT screen dropped right in. Then Amazon had some big sale a few days ago and the BTT TFT50 went on sales for a great price. So...

Construction : 3D printed case. I mounted the relay circuit on the TP4056 PCB. The TIP120, LMV358, PNP current generator circuit is on perfboard attached to a coolplate. Ground loop issue: uV-s make the difference, it's very important to follow...

This allows access to circuit boards soldering from both the bottom and the top during assembly.The box is not water proof and supposed to go into the Stevenson Screen.Printing configurationLayer height 0.2mm0.4mm nozzle15% infillWhite and black PETG...

Instead, each STL is printed as a different colour, or multiple colours in the case of the main STL. This means that you need to align all parts in your slicer before positioning them on the bed. All parts share the same coordinate origin. Any...

 You could also do a three- or four-color print, of course—just make sure not to skip the “Contrast Test” section, below.This is designed so to be completed in two passes on a Prusa MINI (or in my case, one pass on each of two MINIs).  I...

However, you can also insert a pause at the end of the pocket and insert the pin during the print.I am leaving the original axle up in case someone is using a stronger print method or wants to make a remix, but please do not use it.Thus was born my...

Instructions: Options used: - qr_tolerance: 0.001 - per_h: 10 - per_w: 3 - hole_r: 10 - hole_y: 0 - hole_x: 30 - tag_height: 80 - qr_data:...

In some cases, these devices will not be appropriate for each individual, and consultation with medical professionals and occupational therapists must be sought and obtained before use. Design Merits: Silent Operation The flexible hinges are...