sears craftsman 10 miter saw 3d models

This replacement fence is designed to interface with an old model no longer supported of Sears Craftsman 10" compound mitre saw. It also features a recycling triangle with resin identification code 7 (other) and the letters ABS to enable eventual...

This is a replacement drive gear for a Sears Craftsman 10" Band Saw model 113.244513. The original part number should be 64 69162. A friend came to me with this part that had all the gear teeth stripped down from the belt. I modeled up a similar...

This is a replacement miter track bar for the Rockler Featherboard which fits my Craftsman 10-in Table Saw. This smaller table saw uses a different track than the one I had before so I had to modify the bar. It fits the Craftsman 10-in Table Saw...

The miter slot on the Craftsman saw is 16mm by about 7mm deep so I used the same spacing for the holes as bruckj and made the slide fit the miter slot on the Craftsman saw. I had already bought my hardware so if you did the same after seeing bruckj's...

I have a Sears/Craftsman 9 Inch Table Saw and could not find a good file on here that worked. My table saw has a .500 (12.7mm) with the flat to round dimension measuring .400 (10.16mm). Handwheel body is 3.5" in Diameter. The handle knob is 2.5"...

... fillet on the surfaces that led to me printing with supports and then having to sanding it off. I'm not in love with how the surface finish turned out, but it lives under the table of the saw, in a basement, covered in dust, so choose your battles.

... 10 in. ...Compound Miter Saw Replacement trigger. Model No. 315.235360. The original saw's trigger broke and is no longer available to purchase. ... This trigger was designed in sketchup and replaced the broken trigger directly off the 3d printer.

I built this miter saw table for our shop. ...I put Polypro for countertop and ABS white for the bottom shelf and it work great.

This is a replacement laser holder for a craftsman miter saw. You will need 2 screws to attach it to the holes on the saw. ... Designed in fusion 360.

The miter locks that come with the [Powertec Featherboard](https://www.amazon.com/gp/product/B084ZF7SWN/) are not compatible with an older Craftsman table saw that I had, so I designed and printed these so I could use those featherboards with my...

Made this for a coworker; Replacement Craftsman 12" Compound Miter saw handle. The old handle broke off, just had to lightly tap this handle into place. Glue may hold it better, but it is a solid fit by itself. ... Created in fusion 360

... me to print it for you please check out my Etsy page. https://www.etsy.com/CuriosByCalvin/listing/1089294407/137212290-craftsman-miter-saw-handle?utm_source=Copy&utm_medium=ListingManager&utm_campaign=Share&utm_term=so.lmsm&share_time=1632332951144

I couldn't find anything on Thingiverse that matched the ID of my miter saw so I just remixed the one by Kachidoki. ...The part that inserts into the tool is 31.5mm OD and 20mm long.

I inherited my father's Craftsman radial arm saw which he purchased new in the late 60's/early 70's. For several years, the factory on/off switch has been on it's last legs and it finally wouldn't turn on about a month ago. Of course, that switch...

This is a replacement handle for a Delta miter saw. It is designed to drop the bolt into the handle as it is being printed. ... You will need to pause the print at the correct layer to insert the bolt.

This is a replacement handle for a Delta miter saw. It is designed to drop the bolt into the handle as it is being printed. ...You will need to pause the print at the correct layer to insert the bolt.</p> Category: Replacement Parts

The oddly-shaped throat plate insert for Craftsman Miter Saw #137.212290 wasn't too hard to recreate, which is great, since it's been discontinued and no longer available anywhere. Original part # is 2BK8. ...

... to make it I thought others might also need this part. CRAFTSMAN MITER SAW HANDLE 137.212290 2BPS CONNECTOR Note: It appears 3D Printing this part it is not strong. ... I print in PLA and have tried 3 different times now and the part always cracks.

Zero clearance inset / throat plate for Craftsman miter saw (model 137.212290). Bought the saw used and the throat plate was cracked and falling apart. I taped up the remnants and modeled a new one since these are impossible to find. Print with...

Craftsman 113 10" Table Saw Top

I just bought an old Sears Craftsman 10 inch Bandsaw to play around with but lost one of the latches while transporting. ...This should snap straight on.

Sears Craftsman Garage Door Opener Light Cover This was printed with Maker Geeks Ah! Natural Pla with a brim to reduce printing time. The cover is for a garage door opener that is no longer available from Sears. The model is 139.535000. ... Be sure to...

This is a band saw guide for a Craftsman 10 inch band saw model 113.244200. The Sears/Craftsman replacement part number is 328514. I used ABS with no supports. ...Fits just like OEM part.

This is used to clip an outlet box to a Ryobi 10" miter saw. ...I use it for a vacuum switch.

Designed to as a replacement for the Craftsman 10" Table Saw Belt Guard Part #: 60252. I've included the Fusion 360 archive file. It's a parametric design and can be customized in many different ways. ...The Pulley Hole Diameter, Wall Thickness, Length,...

I had trouble finding a miter rail for a Ryobi 10" table saw that actually fits. This design fits when printed on my printer however it should be customizable via the openscad file. ...I've included screw holes for #6 wood screws to attach it to your...

I had trouble finding a miter rail for a Ryobi 10" table saw that actually fits. This design fits when printed on my printer however it should be customizable via the openscad file. ...I've included screw holes for #6 wood screws to attach it to your...

Several years ago, I read posts on message boards asking for information about purchasing a new handle for their 10 inch Harbor Freight chop saw. There are replacement handles available for some saws, but not those with the mounting bolts that run...

If you have the Rigid (Home Depot) 10" Miter saw with the laser line (model MS1065LZA) the insert plate (the orange plastic part) will eventually crack. I couldn't find it on the Rigid tools website but figured, it would work just fine as a 3D...

Miter Saw