seemecnc ezr struder 3d models

Tension release arm for the SeeMeCNC EZRStruder. Made this model because my stepper overheated and warped the original. Must be made from ABS or other higher temp material. ...Original part is injection molded ABS.

Tension release arm for the SeeMeCNC EZRStruder. Made this model because my stepper overheated and warped the original. Must be made from ABS or other higher temp material. ...Original part is injection molded ABS.</p> <h3>Print Settings</h3>...

For some reason I have found it impossible to keep the clippers and tweezers near my Artemis for more than 2 minutes before they migrate elsewhere. ...This caddy clips on to the sheet metal housing of the extruder motor and gives a convenient spot to...

Here's a mount for attaching the SeeMeCNC EZR Struder to a 2020 vertical frame, similar to those found in Chinese i3 clones. ...Two 3mm nuts are required for secure attachment of the nut.

Filament Guide for your Ender 3 that has been updated to use SeeMeCNC EZR Struder. This guide was designed to work with your Mosaic Palette2. It can also be used just fine without a Palette. You can print without support. Print Settings Printer...

Filament Guide for Your Ender 3 Enhanced with EZR Struder, a Cutting-Edge Upgrade from SeeMeCNC. This Comprehensive Guide is Specifically Designed to Integrate Seamlessly with the Mosaic Palette2, Revolutionizing Your Printing Experience. ...Notably, it...

This mount fits perfectly with the SeeMeCNC EZR Struder and 2020 Aluminium Extrusion. I based this design on pheneeny's AM8 printer, which can be found on Thingiverse. You may not need this mount if you have extra M4 Hammer Nuts for 2020 lying...

Adapter plate to use SeeMeCNC EZR Struder in the Ender 3 V2 printer. ...

This is a PTFE PC4-M10 Adapter for the SeeMeCNC EZR Struder to allow a bowden coupler to attach to the in feed of the EZR. ... This allows the 3D Chameleon to load and unload the filament automatically.

Wanted to use BoothyBoothy's Hydra system but didn't see a DD attachment for a SeemeCNC EZR Struder. So I remixed somethings and here it is. Tried attaching this to the Hyrda System but it wouldn't let me for some reason. The link to the Hyrda...

Direct Drive Bracket remixed to use a SeeMeCNC EZR Struder. I recently got an I3 Mega X and have had a hard time finding upgrades. I was already looking at an EZR for my Ender 3Pro so when i found this bracket I decided I would remix it for the EZR...

I've designed this using measures from OpenSCAD files linked from the Duet wiki for revision 2 of the sensor at seemecnc.com, specifically the SeeMeCNC EZR Struder product page. This mount is compatible with an Ender 3 Pro and possibly a regular...

Recently, I acquired the SeeMeCNC EZR Struder for my Ender 3 Pro, but unfortunately, I couldn't locate a suitable cable stay. ...Therefore, I designed a simple one that fits perfectly.\r\n\r\nI secured it with the screws and nuts provided by SeeMeCNC,...

A straightforward fix for effective cable organization on your Ender 3 with an EZR Struder. ...It seamlessly inserts into the depressions of the top cover, permitting cables to route beneath the extruder lever.

I loved Johnniewhiskey's Ender 3 Extruder Cable Chain, but I had the aftermarket EZR Struder by SeeMeCNC on my Ender 3 Pro, and needed a different solution for terminating the extruder chain. I modified the cableChain_Xend.stl and...

The original EZR Struder Chain Mount by PrintsCaspian was holding the chain at an unsatisfactory height, which posed a problem for my specific setup. ...I took matters into my own hands and carefully mirrored the mounting bracket to ensure the chain sat...

You will want to use the SPEED_DRIVE_MOUNT_EZR_STOCK_HOTEND_POSITION.stl For People that want a version where you don't lose any X-Axis work area, they can use the Speed_Drive_Ender_3_EZR_STRUDER.stl This version will require moving the hotend...

Wanted to use my EZR...so I adapted a re-mix

Remixed the Cprints CR 6 SE Filament Guide to fit the EZR Struder.

This modification enables secure installation of the EZR Struder on the Ender 5 by bypassing the extruder mounting plate's interference with T nuts. My Ender 5 Plus model posed a similar issue due to T nut placement, which was resolved by running...

This will allow you to put the EZR Struder on the Ender 5. My Ender 5 Plus's extruder mounting plate blocked it due to the T Nuts for mounting it onto the back. This design allows you to run bolts through the top holes and put T nuts on the back to...

... ...I previously encountered a problem with another design that consistently hit the sides, so I decided to remix this one in Tinkercad by adjusting the angle to ensure the extruder wires and chain align perfectly with the top of the EZR extruder.

I really didn't like the EZR struder mounts for cable chains for my Ender 3 v2 and couldn't find one that had anything other than the hotend attachment, so I just remixed the one I was using for my stock extruder. It fits really snug and secure. Use...

Filament Runout Sensor for EZR Struder Ender 3 OVERVIEW: This filament runout sensor + bracket is designed for an Ender 3 (Pro) with direct drive EZR Struder, used with TPU or any other filament. The sensor costs less than $5 from AliExpress,...

I initially purchased the Original EZR kit, which included top, lever, spring, and fittings, but I found the STL files on SeeMeCNC's Github Page. https://github.com/seemecnc/EZStruder/tree/master/CAD_FILES/STL I'm still experimenting with different...

... original file and hacked away at it until it perfectly accommodated the CMcnc EZR Extruder. ...The result is a snug fit that leaves just enough breathing room for the EZR itself, eliminating the need to make any costly modifications to the extruder.

**Step 7: Final Alignment and Tightening** * Move the EZR Struder sideways in the slots to align the EZR Struder with the hotend. * Tighten all screws, including the one that was previously only snugged down. ... Note: This is a detailed guide and some...

With this spacer, it allows the EZR Struder to be mounted and aligned with the Phaetus Dragonfly BMS hotend when the hotend is mounted with this [spacer](https://www.thingiverse.com/thing:4787514) in a direct drive setup. I used the [PrinterMods...

This needs to be used with the spacer for the Phaetus Dragonfly BMS hotend This spaces out the EZR Struder to be used with many common cheap direct drive upgrade kits for the Ender 3. ...With this spacer, it allows the EZR Struder to be mounted and...

I managed to contact SeeMeCNC who corrected the original Remix's base file for me, allowing me to incorporate the Optical Filament Sensor attachment seamlessly into the revised design. ...The result is a direct bolt-on replacement that's ready to be put...