seemecnc rostock max v2 manual 3d models

LED arm for SeeMeCNC Rostock Max V2. ...Clips on 1" x 1" T Slot and curves around the outside of the print bed.

LED arm for SeeMeCNC Rostock Max V2. ...Clips on 1" x 1" T Slot and curves around the outside of the print bed.

After building my SeeMeCNC Rostock Max V2, I had trouble threading the filament through the top into the small hole and down to the cold end, It wasn't hard, just inconvenient to find the hole by touch since it was above my head. I made this funnel...

I wanted an enclosure for my Rostock Max V4 and it was so new i couldn't find one already being shared on Thingiverse. So I started designing this one. most parts are 3d printed and bolt on using factory hardware. I am terrible at documenting...

This is an adapter to mount the Mosaic Palette Scroll Wheel to a SeeMeCNC Rostock Max v2 printer. It can replace one of the existing side panels on the top of the printer. The cup itself has a helical cutout for the Scroll Wheel’s cable. The...

If you need more on the usage of the filter ring please see my build post at: http://forum.seemecnc.com/viewtopic.php?f=42&t=10409&p=93185#p93185 Print Settings Printer Brand: SeeMeCNC Printer: Rostock MAX Rafts: Doesn't Matter Supports: Doesn't...

If you are not sure which to use go with try the following: **(1) 843XX Rostock Max v2 Assembly - 84310 Top Vertical Support-MM-Alt.stl** **(1) 843XX Rostock Max v2 Assembly - 84310 Top Vertical Support-Drawer-v2.stl** If you are waiting for the...

This is a mount that I created to install the Orbiter V2.0 direct drive extruder on my SeeMeCNC Rostock Max V2. I had been using the Orbiter V1.5 extruder and really like the control that came from having direct drive extruder, but the mount was not...

This is an Idea I came up with for a Raspberry Pi Zero W FIsheye Camera Mount for my SeeMeCNC RostockMax V3.2. Parts needed Raspberry Pi Zero W SD Card Raspberry Fisheye Camera (comes with cable attached) Motioneyes Image for Raspberry...

This system utilizes the original Rambo and LCD controller mounting locations for installation of a [PanelDue 5"](https://www.duet3d.com/DuetAddons/PanelDue), [Duet 2](https://www.duet3d.com/DuetEthernet) (Wifi/Ethernet) and a [JohnSL FSR Endstop...

The build area is not a circle and doesn't resemble a circle. This is NOT the entire build area it leaves 1-2 CM on the outside. This object is much better at testing your X/Y/Z tower endstop calibration. Since it uses most of the printable...

E3D Titan extruder mount for Rostock Max - SeeMeCNC

Enclosure Part for the Rostock Max V2 or any other printer if you modify the design

This is a side panel for the SeeMeCNC Rostock Max V3 with a single 60mm fan grill and mount. This is perfect if you want to add some cooling to a part of the printer covered by the panel. ...This was modeled from the SeeMeCNC GitHub for the V3

This is a side panel for the SeeMeCNC Rostock Max V3 with a Dual 60mm fan grill and mount. This is perfect if you want to add some cooling to a part of the printer covered by the panel. ...This was modeled from the SeeMeCNC GitHub for the V3

It turns out that the stock SeeMeCNC Rostock Max V3 requires a narrow top drawer. So print the part 2DrawerShell-V3-Stock.stl for a stock V3. You will then need to print one V3 Drawer and one standard size drawer. ...But I give you a choice of a plain...

If you want to illuminate your cabinet, here is the rocker switch box I modeled: http://www.thingiverse.com/thing:1421639 and here are the extrusion mounts for the LED strips: http://www.thingiverse.com/thing:1702064 Print Settings Printer Brand:...

Print Settings Printer Brand: SeeMeCNC Printer: Rostock MAX Rafts: No Supports: Doesn't Matter Resolution: 0.2mm Infill: 100 percent Notes: Printed @ 0.2mm layer height with a 0.4mm nozzle using ABS with 100 percent infill. The only support I used...

... of dreading it. Requires x6 drill holes in the top of Rostock Max V2. Use a template for accuracy before drilling or mark where you want the holes and remove the top to drill. ...Drill press recommended or tool to ensure perpendicular Drill Bit.

This is a full enclosure for the SeeMeCNC Rostock Max V2. It has double doors on all three sides that swing open fully allowing easy access to the build area. I designed this enclosure to create a heated chamber and to (hopefully) capture the...

... the design, but it means you may have to bend the mounting plate up slightly to fit the Cover of the titan on. I can loosen that opening up if people desire. Print Settings Printer Brand: SeeMeCNC Printer: Rostock MAX Resolution: .3mm Infill: 35%

These are the brackets needed to make an enclosure for your rostock max v2. You will need 3 base and 3 top pieces. You can print 3 at a time with the build area. Locate the brackets on the extrusions and bolt the brackets to the rostock's top and...

I printed these to help keep things organized around my printer. There are 2 version. One is just a simple tray, the other has a tool holder at one end for storing extra nozzles and standoffs for my quick change hot end. ...

... ...The next version will include 2 holes for M16 switches. Here's the linkhttp://www.thingiverse.com/thing:1547459 Print Settings Printer Brand: SeeMeCNC Printer: Rostock MAX Rafts: No Supports: No Resolution: .25 Infill: 30 Notes: Made with ABS

Print Settings Printer Brand: SeeMeCNC Printer: Rostock MAX Rafts: Doesn't Matter Supports: Doesn't Matter Infill: 30% Notes: These should print just fine with no supports. I used Black ABS and HD green PETG. The nylon will need a finer resolution...

This is the stock extruder platform for the Rostock Max V2 with 3 tabs for layer fans.

This is an adapter to use HugoHuge's Filler on a Rostock Max V2. ...It slots in place of the original laser cut spool holder arms.

Replacement for the three spacer parts that hold the extruder and its stepper motor to the extruder bracket on the Rostock Max V2.

Print Settings Printer Brand: SeeMeCNC Printer: Rostock MAX v2 Rafts: No Supports: No Resolution: .2mm layer with .5 nozzle Infill: Doesn't matter Notes: Printed in Microcenter Inland ABS at 240 with the bed at 90 on glue stick. I use a Prometheus...

Nimble mount for a Rostock Max V2 by SeeMeCNC with the PEEK Hotend. See https://www.thingiverse.com/thing:2184991 for firmware settings. Rotate and print with supports. Or, if you really want, skip the supports. 6/6/17 -- Reworked a bit,...