silicon atom model project

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_left_port_length = 50 custom_top_port_corner_radius = 5 pattern_element_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

The COMPLETE Thieves Guild bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! This set includes: Thieves Guild AdeptsVery little is known about the legendary Thieves' Guild in...

https://www.youtube.com/watch?v=Nn9B46IjsVU ______________________________________________________ ENGLISH ______________________________________________________ Only tested on T12-X, but can work on equivalent models with boxes of the same...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

Check out the rest of furniture models from it, as they will fit nicely with this mini set! Bar pieces have special connections that allow you to attach them to each other in an unlimited amount of ways, and create any shape of bar that you desire,...

Note that the earlier XT (and other Zumo models) have a 12 volt to 5 volt conversion, so as far as I know this will only work with the XT2 mount (which has a slightly different pin layout from the other Garmin mounts)I have not tested the Carpuride...

3D print was carried out so they look perfectly visible under their massive sizes : as models that architects make in the form that represents its conception in such proportionate detail they have since their youth seen so that in front it leaves...

- The barrel at the front stabilizes the cars but is limited in size, preventing some models from fitting inside. However, a vast majority should fit without issue. PRINTING: - I print the main body and shaft separately from each other, as well as...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

MP4 Model with mathematics. MP5 Use appropriate tools strategically. MP6 Attend to precision. CSTA Standards 4.2.2 Collaboration NGSS M.S. Engineering and Technology Standards Strand 1 Define a design problem that can be solved through the...

This thing is a two-part shield for the head of your Ryobi trimmer, model number: RY40220. It’s a bit crude, and I planned on making it look smoother, but this thing really works! By narrowing the gap that the grass can fit through and diverting it...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

 Some require the models to be rotated so that they share space with their neighbors.AssemblyEach tray is comprised of 4 (or 5) rows.  Each row comes in two parts (so they fit on smaller printers like the Prusa Mini) and need to be glued...

Thread the wire through the lower cutout of this model and attach the new wire to the switch by pushing the two quick connectors onto the switch's terminals. ...Press the switch into its place in the case. </p><p>Cover the electronics (<a...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 1 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

I recommend scaling the models 101%-103% if you plan to mix ABS and PLA. Note 2: My RH hotend is all metal. Printing above 230C with a PTFE lined hotend isn't usually recommended. How I Designed This I ended up making five different iterations...

Taller models have a tendency to cool in the middle and pull the bottom up at the corners. If your workspace/office is 75 degrees and you printer is not in an exclosure you should probably use some kind of adhesive. I found Glass+Glue worked for me...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

 On my ESC I have to start with the minimum setting (effectively the throttle channel on an RC model), which I believe is a great safety feature.  BTW you can also program your ESC using the knob as if it was a throttle control, if your device...