smartthings hub v3 3d models
40982 3d models found related to smartthings hub v3.thingiverse
Simple bracket for mounting a smartthings hub on the wall. ...Print Settings Printer Brand: Wanhao Printer: Wanhao...
thingiverse
Samsung SmartThings Hub Wall Mount - Mount to the wall with some 3M Command Strips. This mount is designed for an older hub with the AA battery bay. Mount was created in Fusion360, file included here. ... Enjoy,
thingiverse
SmartThings Hub (gen2) wall mount. This prints vertically without supports. It mounts to the wall with 2 screws. It is designed with the cables at the top. You can slide it out if you need to work with it. ...Note: There is a remix with access for the...
thingiverse
For mounting your SmartThings Hub on the wall with the cables entering from the bottom, so that you can see the status light on the top. There are two versions - a deep one (40mm) which the hub should slip completely into leaving some space the head...
thingiverse
This is a sweet mount, prints very nicely and is simple to install your SmartThings 2018 (Generation 3) hub with. Just place the hub in the opening and give it a simple twist. It's quite strong and can be used on the wall or ceiling or under a desk...
thingiverse
Minimalist wall mount for the Smartthings V2 hub. Printed in white, it's almost imperceptible. You will need to print with supports, for the prongs that snap over the top. The hub is a weird asymmetric rectangular shape, where one end is higher than...
prusaprinters
Minimalist wall mount for the Smartthings V2 hub. Printed in white, it's almost imperceptible. You will need to print with supports, for the prongs that snap over the top. The hub is a weird asymmetric rectangular shape, where one end is higher than...
prusaprinters
A remix of the SmartThings Hub (Gen2) Wall Mount - Ports on Bottom by neonpolaris. When I sliced the model in S3D it was two objects and the print would have been very weak structurally. ...I repaired the model so it is only one piece now.</p> ...
thingiverse
A remix of the SmartThings Hub (Gen2) Wall Mount - Ports on Bottom by neonpolaris. When I sliced the model in S3D it was two objects and the print would have been very weak structurally. ...I repaired the model so it is only one piece now.
thingiverse
A quick hack to allow mounting @JellyTitan's minimalist Hub v2 mount 90 degrees so I could put it between two wall studs in this unfinished hallway. ... Source docs:...
thingiverse
My hub was very snug in the original, so I also added 1mm to the width and depth of the opening for the hub. It's still snug, but not enough to warrant reprinting. I had printed the original with an infill of 35%, but immediately snapped off the top...
thingiverse
In short, though, this hub mount is printable on a small printer (the MPMD has a print surface of 110mm in diameter) and snaps together without any extra hardware or glue. I used Cura as my slicer and enabled tree supports to support the top of...
thingiverse
... front status light visible. The ports are facing upward and the hub can slide it out for service. ... Notes: - The original design is created by cmar (2051324) - There is a remix with access for the ports on the bottom by neonpolaris (2232385)
thingiverse
another version of a geodesic dome hub system using a series of hinges. uses a screw to hold to a wood strut. 3 for a triangle, 5 for a pentagon, 6 for a hexagon. use supports screws and struts not included. ...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=723983 Instructions Using the following options: nuts_across_flats = 6.8 flange_height = 0 axle_diameter = 5 axle_thickness = 5 nuts_external_diameter = 7.5 radial_holes_r_vector = 17...
grabcad
Concept idea proposal for SmartThings (http://www.kickstarter.com/projects/smartthings/smartthings-make-your-world-smarter). ...Unfortunately my design was not shortlisted.
thingiverse
Stand for smartthings to lift off counter. It perfectly outlines the profile of the device. ... I used double sided tape to keep it in place.
thingiverse
SmartThings Button holder that can be attached to wall plate. Second one initial design, it's thinner, with 2mm back side, un-tapered hole. Enjoy! ... Thanks
thingiverse
UK Light panel for Samsung SmartThings Button This cover replaces the existing light switch with a bracket that holds the SmartThings button and slider to allow the power to be manually enabled / disabled preventing the light been accidentally turned...
thingiverse
Used to mount the magnet of the smartthings multisensor to a shed door. The sticky pad soon became "Unsticky" so I created this to mount the magnet on the door. ... Printed on a Ender3
thingiverse
I couldn't find what I was looking for so I whipped up this shelf quickly and then printed them for my Samsung Smartthings WiFi mesh nodes to sit on.
prusaprinters
A wall mountable plate designed to hole a SmartThings button.Remixed from:https://www.thingiverse.com/thing:3827965 and https://www.thingiverse.com/thing:5128845 Print with the show face on the bed, supports are not required if you have your...
thingiverse
This is the camera stand for the SmartThings Cam RC8335PRO. The original broke, so I went ahead and threw together this quick version of it. It is not 100%, mostly minor details though that I was either unable to measure or didn't want to spend...
thingiverse
Make your SmartThings buttons portable! --<strong>Two Versions</strong>-- Two Button Version Four Button Version You may want some 3M tape under each button to hold them in. If you use tape it might be tough to get the buttons out of the...
thingiverse
I have designed a simple Smartthings button holder for a pole but also one you can mount somewhere on a wall. Its a tight fit so for the wall mount you will have to use tape or a suction cup to remove the button. The pole mount is just simply...