smg modeling

The tolerances on these can be somewhat tight, but they came out beautifully on my Bambu X1C.Model specific notes follow:cards_box_1.stl, cards_box_2.stl - Print one of each. You can add color on layer 4 or 5 (depending on line height) to make the...

So, I made these 2020 fasteners.This is a remix of hallonhatt's: 3030 extrusions quick fastener:https://www.printables.com/model/80548-3030-extrusions-quick-fastener-fits-prusa-i3-mk3I printed at 0.16mm line height, 100% infill, with black Overture...

... I use Fusion 360 to design the model. While trying to maintain a supportless design I tried many different options but I still end up with the dovetail design. I do not want to use any external fasteners so this limits the design options further.

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

Not a problem with a well-tuned MK3S+.    The box was printed usingFilament                                              ...

"Pipe" model: A 4mm bowden tube will NOT fit between the 3mm gap of the emitter and the receiver of a standard 3D printer Optical EndStop without some work, cutting the tube or the emitter and the receiver thiner, etc... Also the "Pipe" idea will not...

March 23rd - Created a smaller prototype mockup for the bottom, mid, and top tray using measurements from the full-sized model. Experiencing corner lift on the middle tray, even with brims, and the lid/bottom of the middle tray is about 1mm too...

Here's the link to his project: https://www.printables.com/model/377909-3d-benchy-tensegrity-sculpture Problem Statement:With a partner, you will design and create a single custom Tensegrity Structure of equal complexity or greater as the tables...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protectionSuperior...

Some of the models are difficult to hand-launched and should be tested with a 1/16" rubber band instead. A slight elevator-up reflex is required for flight. This is accomplished by latching the elevons up on the relex tabs on the aft end of the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

Thread the wire through the lower cutout of this model and attach the new wire to the switch by pushing the two quick connectors onto the switch's terminals. ...Press the switch into its place in the case. </p><p>Cover the electronics (<a...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

Subscribe Now! A very good model from Multiverse3DDesigns. Remixed to support free to do timelapse. https://youtu.be/H-_2R-mKoMo <a href="https://youtu.be/H-_2R-mKoMo"><img...

There you can find links and reviews about quality hobby products. https://MyHobbyTools.com ✔ 3D PRINTING My Favorite 3D Printers 3D Printing Tools 3D Printer Parts ✔ ELECTRONICS Batteries and Chargers Soldering Kits & Modules Multimeters...

The 3D model is solid. To make the vane pattern in it, set the number of top and bottom layers to zero and select a grid or triangular infill with a distance of about 10mm between lines. To ensure rigidity, aim for at least 1mm walls (3 perimeters at...

There is currently a mock-up indicator shown in the model for demonstration purposes. PDF files for all required screws are included. The Repeat-O-Meter is used on a flat surface plate to find local dips or high-spots. Using this device can tell...

Water cooled esc's are easy off the shelf for model boats etc and I may build enough space for a cheap (solar fountain type) water pump in the bottom. This could then feed the esc and also a water cooled motor plate. I also have a retro styled...

current problems: - comments and filenames are mostly in German language - some of the mounting holes in the pcb are not at the exact right place - the pcb was designed with easyEDA and not with an open source program like KiCAD, which is compatible...

The bands were modeled separately so they wouldn't require supports and be stronger. I printed them on their sides and used a brim as they had less surface area. They will have to be glued. The main body and battery compartment required supports. I...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

... By using this model, you can get students to develop their own design or work as a team to develop a shared design. Race the vehicles based on your own design criteria or see whose design will go the furthest. Who can build the lightest, fastest?

A .3mf file and pre-sliced .bgcode file is available along with the STL models. Also prints well on a Bambu Lab P1S.Assembly/MountingThe inner fixture can be held upside-down to desired mounting position for marking the mounting holes. I found it...

I tried to faithfully model the design of the original tapered bin, including its small brim, though I did approximate the feet a little. As seen in the second picture, it fits securely despite not having a flat bottom and seems to hold its contents...

To-do * range test video * sans gaming video * doom gaming video * radio demo video * improve software a little bit * and finish wiki ofc Find the project elsewhere * [OSHWLab](https://oshwlab.com/leoneq/konsola) for schematics and PCB source *...

... - Schematics:  Goggly eyes are optional, but they improve performance and friendliness of the finished project. Modelled using tinkercad & blender. ...

Supports: YesWhole star: If using Cura we recommend using the [Tree supports](https://support.ultimaker.com/hc/en-us/articles/360012614559-Experimental-settings) option and adding a 'Brim' to help the Tree supports adhere to your print bed Half...

Subscribe Now! A very good model from Velrock. Remix to support free and printed. If you are looking for Baby Yoda remix in this print: https://www.thingiverse.com/make:872409 Time-lapse print video : Resin :...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 1 stencil_shape = 7 stencil_size = 40 stencil_mirror = 0 custom_back_extra_port_x_size = 30...