smithsonian 3d print files

Bollards (cross)- print several pieces and glue in vicinity of chocks. Ballast tanks can be filled through ballast vent pipes and emptied by syringe with flexible pipe connected to sounding pipes. Pay attention during ballast operations- excessive...

You can also refer to this video from Embrace Making for dissasembly assistance, it helped me so much when I was trying to do this I've tested it on all-metal version with dual-fan setup, you can refer to my klipper config if you need to (Please...

Our design is nested and compact, which means it takes less time to print one set. The board we use makes wiring and assembly more accessible. With an internal battery charging circuit, you don't need to remove the battery for charging. To control...

Instructions: - Use the following options to personalize your back to school nameplate: - Center: 0 - Rule font: write/knewave.dxf - Rule Decoration: txdes - Build Plate Selector: 0 - Read: 1 - Text Height: 5 (Text_Height) - Length: 190 - Text Height...

I did a filament change part way through the print to green, to allow for the highlighting of the symbols, my call-sign etc. Finally, using this layout, there is plenty of space under the top panel at the front, under the LCD / VFO area. I am now in...

Due to the adhesive discs on the wind turbines, a print bed with at least 210x210 mm is required. There are 5 different lids. With NabeTest you can adjust the bearing seat of the wind turbines with scaling in X and Y. The labyrinth ring is glued to...

Assembly Once all the pieces are printed, start by running the wire through the hole in the center disc of the inner_reel so that equal lengths are protruding on either side. Thread the wires through the holes in the upper_half so that the wire on...

I printed the coupling with TPU and fits onto the gear wheel of the stepper motor and onto the self-locking nut M8. The stepper motor probably comes from a Canon inkjet printer. ... Are needed: 1x stepper motor 35 mm SMJ35-4831-B or identical 3x...

Designing and drawing this model required over 1200 hours of work, and printing it took an estimated 2000 hours. The model uses various colors in PLA, including True Red (10 pounds), True Yellow (2 pounds), True White (8 pounds), True Black (4...

Two are required, the shape is rotationally symmetrical so only one model is needed, and printed twice. The jig is 2RU (3-1/2") high which is the same as the smaller PDP-11/03 chassis height. To use, simply push the jig into the rack from the...

... Carl XVI Gustaf of Sweden presented Pink Floyd with the Polar Music Prize for their contribution to modern music. Thanks for checking in on us and for your ongoing support.CR8ED Out Of Hand Sculptor - Sandy Campbell3D Scanning and Printing - CR83D

... passt und einen neuen dazu passenden Deckel.</p><p><strong>Bitte stellt Euren "Make" ein. Danke. :-)Print SettingsRafts: NoSupports: NoResolution: 0.2 mm layer hightInfill: 15 %

For this team project i worked with Joanna Su (link) Problem Statement: With a partner, you will design a “2D” placard using Solidworks.  You and your partner will have the same design which meets the constraints below, and you will EACH use...

To assemble this beast, you will need two of each part with the exception of the jaw and the lower teeth which only one of each is required, and the piece called peg_1 needs 10 of each to make the hinges, I tried having them being part of the limb...

Just follow these three steps: 1st step: Print the most used* clip: clip_0_0.stl 2nd step: Select the clip_X_Y.stl with X > 0 for wider clip Select the clip_X_Y.stl with X 3nd step: Select the clip_X_Y.stl with Y > 0 for higher clip Select the...

I increased the tolerances a bit in the last version 1.1 but I didn't printed it because the version 1.0 is already working good for me (after sanding). So I hope it will be ok for you. Anyway, you will still have to remove the supports and sand...

... why I think I have such poor colors and so much diffusion in my photos. Once the pinhole was made, I cut it and taped it to the backside of my printed adapter with duct tape that I then covered with electrical tape (to avoid internal reflections).

... holes for the magnets in the block. The Display Base was too large to print as a single part on my printer, so I split it into 'a' and 'b' parts. ...The two halves of the Display Base can be connected using two M3x12 screws, washers, and nuts.

BEC set to 3.66V RMS --> VCC Hall sensor board pin 24 Jetson (physical pin == number printed on pcb) --> D0 Hall sensor board GND to GND This configuration is listed on Slack from @Doug and @Tawn (https://donkeycar.slack.com). Thanks to them! I use...

... albums of all time, and they ranked Hendrix as the greatest guitarist and the sixth greatest artist of all time. Thanks for checking in on us and for your ongoing support.CR8ED Out Of Hand Sculptor - Sandy Campbell3D Scanning and Printing - CR83D

Depending on filament flex, shrinkage, and printing tolerances, your screws may extend too far into the front grid and begin to push out of the front panel. When in doubt, try a screw one size shorter than suggested.</p><p>There are two mounting...

Duplicate and mirror the mount and print the 2 mounts. 12/18 update: made a servo mount adapter that lets you move the servo back to the stock battery tray location. use the stock M3x8 screws. you'll need an M3 (3mm) threaded rod to extend the...

What with trying to design mods for my printer, I figured having a virtual model would be super handy - and it got totally out of control!\r\nAs I've seen people complaining about not being able to get plans for the acrylic parts in case they break,...

So you can print and assemble the case and then add the expansion board at a later date - if you are having trouble getting your hands on the m.2 board (ETA Prime's caused it to go out of stock at Amazon). This case may also work with the...

Insert that STL into your printer, as it takes longer to print than you need to set up the pi&ssd ##2. Just follow [these instructions](https://www.raspberrypi.org/forums/viewtopic.php?t=44177). It doesn't take as long as *paulv* wrote in 2013.... I...

I also have a light-sensitive resistor on it and plan to add a sensor at the rear and one facing down to prevent the robot from driving off cliffs.\r\nI've got plans to be able to extend the length of the track assembly by adding a third cog, but I...

PRINTING ----- Nothing needs supports. I use transparent PLA for everything. I would recommend using the same colour for all mounts, but you could also colour them to match the cap, or code them to the country they come from or something if you...

... any surface with screws or nails. I may explore a way to use these to make a suspended version of the dispenser. Nota3: don't mind the colors. I ran out of black PETG during the print and had to switch to white. ...In the end it's not that bad.

This is my first attempt at sharing a 3-D printing model. History: A few years ago, after purchasing a CNC machine, I decided I would design a D-Handle that I could use for my Porter-Cable model 450 compact/trim router. I believe I came up ...

#Gateway 1:100(ish) Gateway These are meant to be (relatively) easy to print and still fairly true to life. The models are made to fit together and come apart much like the real deal. Components slip/sit/snap together. These are the same scale as...