snap on models

They are designed to snap onto the small lip on the top of the inserts and therefore won't fall off, even when a shaken around vigorously.When you slice the covers, make sure to change the bridging angle to 45°, as this makes for much shorter and...

Here is a simpler version of the ID Badge carrying iPhone 7plus cover: https://www.thingiverse.com/thing:2521191 Just snap your phone and ID badge into this thing and you'll be set. Here's a vid if you prefer a live action visual (just imagine it...

... with only minor modifications. ...The key changes include: Removing the hinges to achieve a more compact design Extending the snaps slightly to ensure a secure fit Adding some tolerance to the snaps and hinges so that the top wouldn't shift around.

Finally, here's a fully working version of my snap-on device for the PS4's DS4 controller. This device features a Teensy 3.2 board with a 0.96" OLED display and 15 additional buttons - three around each analog stick and four on the backside...

**Instructions** Printed with a layer height of 0.3mm in PLA, or Print with 0.45mm layer height in Taulman T-Glase as shown on the pictures (update Cura settings to use a 0.5mm nozzle), heat up to 220°C at 107% flow rate, set the bed temperature to...

DJI Spark Propeller Protective Guard.\r\n\r\nThis protective guard is my second design, and it easily snaps on without any screws. It prints in one piece without supports, with holes at the ends for connecting wires to provide 360-degree...

I needed to replace my Igus linear bearings (RJZM-02-08) on my Prusa mk3 as they were getting loose (they were never that tight-fitting to start with) so decided to print some (like many others have). I wasn't that happy with the published ones that...

To attach simply hook the short arm around the back of the frame, then work the long arm around the front (force required) until it snaps into place. ...The hooks on each arm clear the Z axis so the holder can be slid up or down the frame to a...

... Print the hook part flat and the wall part on its side. A 0.6 mm tolerance is used for the snap-on part, and a 1 mm tolerance is used for the wall part to fit snugly in the slot. ... Please leave a comment and share pictures of your creations!

You simply snap the clip onto the Z-axis endstop, then print the clip itself. Next, attach the glass plate and you're finished! ...No modifications are required to the printer or additional hardware is needed.

Reworked the cover to ensure shorter legs that allow for clearance, enabling a tighter fit that resists vibrations from the fan snaps into 40MM holes. ... Print Settings Printer: HICTOP Rafts: No Supports: No Resolution: 0.1mm Infill: 10% Notes: PLA

This is a 25mm button though it should scale up quite well if needed!The button has a small peg in the centre allowing you to attach the various face plates, these are also removable so you can mix and match as you like!There are 4 holes for...

Just a simpler version of the ID Badge carrying iPhone 7plus cover: https://www.thingiverse.com/thing:2521191 Just snap your phone and ID badge into this thing and you'll be set. Here's a vid if you prefer a live action visual (just imagine it...

This is an adapter to use "chassis ears" with 1/8" phone jacks with a 4-Channel Snap On oscilloscope that uses banana plugs. Assembly: You may find that you need to ream the holes slightly for the hardware depending on material used, I simply used a...

This is a battery pad engineered to securely snap onto the bottom plate without requiring any screws or adhesive, ensuring a seamless assembly process. Printed with ninjaflex at 30% infill and 0.4mm wall thickness, it boasts a soft, squishy texture...

Almost the same as the original from which it was remixed. Changes: removed the hinges for a smaller form factor extended the snaps a bit -- they had a tolerance for the hinge and the top would move around otherwise Category: Computer

... to seamlessly integrate with 2020 aluminum extrusions. ...This ingenious device snaps effortlessly onto the top bar of your printer, expertly guiding filament from above directly into the extruder, ensuring smooth and consistent prints every time.

I used the snap-fit file, and I see a lot of decals out there, but nothing with designs for a 3D printed cover. I only found one other design, a Venom design, which looks incredible. ... You can find the others here: Original Blank: ...

remix of https://www.thingiverse.com/thing:3184481 inspired by https://www.thingiverse.com/thing:930831 a bathroom hanger for one of those bath trays that has: - rod width: 2.5mm - distance between rods: 23mm it just snaps in and holds your razors :)

A ring that snaps the top of two plastic "party cups" together. Cups should have a top diameter of approximately 92.4mm. ...Intended use is starting seedlings, but there are probably other uses.Print flat with supports and I used PETG.

After printing, snap the parts together like in the video, then slide in your controller. Set your control stick to the right thumbstick and your throttle to the left trigger. For extra spring tension, snake in a short rubber band through the...

... must be firmly snapped into place before being slid to the desired height. Due to the snap-in installation process, users may need to increase the number of perimeter layers when printing with PLA or opt for a filament that offers some flexibility.

... Support Settings: No supports are required. Printing Settings: Resolution: 0.2 Infill Density: 15% Tips and Notes: To assemble the printer, start by attaching the bottom hook first. Then, simply push it back and it will snap into place securely.

... at all! Since the legs didn't turn out quite as expected, I came up with a Plan B: I decided to disconnect them so they snap onto their correct locations. ...Now my printer is busy running some tests for me while I finalize the other details.

This is an adapter to use "chassis ears" with 1/8" phone jacks with a 4-Channel Snap On oscilloscope that uses banana plugs. Assembly: You may find that you need to ream the holes slightly for the hardware depending on material used, I simply used a...

I'm installing a no-bolts strain relief on my Ender 5 Plus, which should also fit other Ender 5 models, possibly even the Ender 3. ...To secure it in place, I simply slip it on and use a zip tie to hold the wires tight.

Fan guards seamlessly integrate with 40mm fans, snapping securely into place without any hassle. For a more permanent fix, simply apply one drop of super-glue to the corners and you're good to go - no need to worry about obstructing those four...

This cover fits snugly into the fan opening, although it did require a minor tweak to snap perfectly in place, which may result in an imperfect design. ...After making some adjustments to my original design, I reprinted and uploaded the revised version;...

I used the snap-fit file, and I see a lot of decals out there, but nothing with designs for a 3D printed cover. I only found one other design, a Venom design, which looks incredible. ... You can find the others here: Original Blank:...

... it at https://www.thingiverse.com/thing:1692395. This model works perfectly, but I noticed that the part doesn't look great on my printer due to the overhanging features. ...To fix this issue, I've created a modified version with reduced overhangs.