snapmaker 2 3d models

Snapmaker 2.0 Wall Mount for CNC-Head with Snapmaker Vacuum Attachment I designed this wall mount for the CNC-Head of Snapmaker 2.0 with their provided Vacuum Attachment installed.

I wanted to store my Palette Pro 2s on top of my Snapmaker enclosure and utilize a proper PTFE guiding system. I could not find anything that fit my setup so is designed this to match my setup. On my rail I have another one, in case I am storing a...

With this Add-on you can store some things on top of your Snapmaker without having fear of breaking the top section of your snapmaker.

additional spool holders for Snapmaker A350 Enclosure1x up to 300mm spools - left  overhead frame mounting1x for smaller spools - rear left below frame mounting  you need per holder 1 threaded rod M8, 115mm length and 2 M8 nuts, M4x16 cylinder head...

You only need a few extra parts: 2 x M4 nuts and 4 x M4x12 or M4x14 screws (DIN7984 like the screws from the Snapmaker) I used the drag chain from https://www.thingiverse.com/thing:4783019. For my A250 I used 17 links and maybe I rotate my back...

I was looking for a simple solution to attach my power supply to my SNAPMAKER A350 enclosure Follow the link : https://www.printables.com/model/144674-snapmaker-20-a350-power-supply-external-mount

Protect your Snapmaker hot bed power cable from sagging and wearing through with this simple 90degree clamp and cover.

Scaled to fit all snapmaker tools, screws ,bits etc. ... 7 Drawers + 1 large drawer for bigger parts.

I made a remix to have the bottom part (attached to the x axis of the snapmaker) in only one solid (previous model was in 2 and it was not possible to slice correctly on Luban) On the top part I adjusted the length between the axis for the bearings,...

With the release of the dual extruding head from Snapmaker, I wanted to put 2 Sunlu filament boxes inside the Snapmaker enclosure. For the front Sunlu filament dryer, I used PoetikDragon design (https://www.thingiverse.com/thing:5681629). For the...

I Added a CableChain Holder to fix the Chain of the original STL to the Z-Axis of the Snapmaker. For the Snapmaker A350 You'll need 18 ChainLink parts and 22 Chain Link Clips. ... I advise you to print a few clips more because at my print I damaged a...

(2) M3x4x5mm inserts inside base to attached to bed (4) M3x6x5mm inserts outside on Cap (2) M2 x 6mm Hex socket head cap screw to attach green socket connector to base (2) M3 x 8mm Hex countersunk screw (or reuse snapmaker screws) to attach base to...

This is an updated version of my snapmaker tool head holder using the quick release system. ...this can be mounted onto the back of the linear modules.note, don't overtighten the screws, the plastic will crack.

I was having problem with my snapmaker calibration so I found this useful instructables that showed how to calibrate with a laser pointer. https://www.instructables.com/Calibrate-3D-Printer-or-Other-CNC-Machine-With-Las/ Naturally I wanted...

Print a total of 2 normal and 2 mirrored Body_v_shim.stl and 8 Wing_v_shim.stl, a couple nut pushers, and 4 of each linear rail rest files. Uses these screws (https://www.amazon.com/gp/product/B0BLNMLHYG) and these nuts...

Je n'ai pas trouvé de solution plus simple pour brancher mon alimentation sur mon boîtier SNAPMAKER A350. ...J'ai également modélisé une version qui se fixe sur la partie inférieure de l'enceinte, mais je ne l'ai pas encore testée.</p>

These are designed to use the same M4x10 flat head screws that are used to secure the 3d Print Bed and attach nicely to the side of the Snapmaker for a clean look and easy storage out of the way of any moving parts. ... (Power supply holder is not my...

... the shelf at the bottom so that no supports are required for printing. ... It uses a 50 degree angle, but printed very well on my Snapmaker using Overture's Black PLA.I used some 10mm x 5mm magnetics from Amazon: https://www.amazon.com/dp/B0CJ6NYNZ6

Need to Print: (2) 3 wire Cable Clamps (1) 2-3 wire Cable Clamps (3) XZ-Cable back supports (5) X-Cable back supports (1) X-Chain Adapter Head (1) X-Chain Adapter Control End (1) XZ-Chain Adapter Upper (1) XZ-Chain Adapter Lower (1) X-Cable Clamp...

You can find this item on Printables here: https://www.printables.com/model/153187-snapmaker-20-module-head-mount-for-enclosure This is a mount to hold 2x spare module heads and spare accessories that slots onto the side of the enclosure for an A250...

the lower right hand side means the tool head doesn't have to be lifted very far before it can be removed and the longer left side means it is secure and gives a large edge to locate the tool head before sliding it in place.this is the 3rd attempt to...

Spool hub and side wheel - keeps the filament spool in place and stable, ensures consistent easy rotation as the printer head moves.This should be compatible with most if not all Snapmaker printers that have spool arm design as in pictures. I've also...

With the recent release of the Snapmaker Quick Swap plates, I needed a way to store my unused beds in storage. With the Quick Swap Plate attached to the bottom of the bed, they do not sit flat in my drawer, so this part acts like a tray for the bed...

AboutI wanted to be able to conveniently place my Snapmaker's display on top of the enclosure and turned to the side, however wanted to keep it easy to move back to the enclosure and up again. ...So I've created this magnetic mount design that can slide...

But I had changed where the Snapmaker Spool mounting bar hardware was located on the enclosure. I put it on the back of the enclosure flat against the back acrylic panel. See pictures. While the original design worked fine, it was hard to...

For those that want to play with it themselves, I have also attached the starting place for things to be attached to the end of the Snapmaker rails so the screw holes match. In the mean time, the initial one makes for a great tilted desktop...

This is a mount to hold 2x spare module heads and spare accessories that slots onto the side of the enclosure for an A250 or A350 Snapmaker. The one photographed features an extra pocket on the side for other accessories but I've uploaded another...

Den Z_Axis END Halter habe ich neu entworfen, und zwar so dass man den Snapmaker Konverter anbringen kann. Somit muss kein Kabel zerschnitten und verlängert werden. Es wird das Kabel vom Kontroller in den Konverter gesteckt und mit einem 2ten...

Den Z_Axis END Halter habe ich neu entworfen, und zwar so dass man den Snapmaker Konverter anbringen kann. Somit muss kein Kabel zerschnitten und verlängert werden. Es wird das Kabel vom Kontroller in den Konverter gesteckt und mit einem 2ten...

Install a Dial Indicator on a Mount with Lug. ... Utilized threaded inserts include: 2 x Ruthex M4 1 x Ruthex M5