snapmaker filament guide 3d models

As before I have uploaded the .step files if you should wish to remix etc. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0.16 Infill: 20 Filament: Surreal PLA Orange Notes: I printed with supports and...

Humidity is relative to ambient conditions, but it is a wet UK autumn @ > 98% and the cabinet currently stabilizes at circa 25% so I am also using it to condition filament for future use (whilst printing) Not yet used in summer. If necessary, a roof...

Optional for multicolor on single color printer, as shown in pictures: pause and change filament at 0.45mm. Also can be printed at 0.2mm if scaled up to 1.333x for a bigger glider! The F44 can be printed on a 100mm or larger bed, the T22 requires...

Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No Supports: Yes Resolution: 0.2mm Infill: 20% Filament: Gizmo Dorks ABS Yellow Notes: Prints on its side, a tiny amount of support is recommended for the tabs which will be off the print...

They are intended as a "better than nothing" solution in response to lack or equipment in the Covid-19 pandemic Print instructionsPrint Settings Printer brand: Prusa Printer: I3 MK3S Resolution: 0.3mm / 0.2mm Infill: 15% Filament_material: PLA, PLA+,...

Printing: I used a Prusa Mk3s and Atomic Filament orange PETG at 0.2mm layer height, 2 perimeters, 3 top/bottom layers, at least 25% infill (the attachment loop is the only place there is much infill and you want it strong). PETG strongly...

(5 loops will give more strength and significantly decrease print time with minimal increase in filament use.) 0.20-0.28mm layer height. While larger layer heights will give you a faster print time, smaller will give you a smoother edge. 0.4mm nozzle...

"Look Ma, no wires!" As with my other workups: B-25 Mitchell https://www.thingiverse.com/thing:4121096 F4U Corsair https://www.thingiverse.com/thing:4178322 Il-2 Sturmovik https://www.thingiverse.com/thing:4132256 EDGE 540 46”...

 If you have the proper filament colors, no painting is needed.The assembled model is 200mm tall.Enjoy!...........................................................................................................**Print Instructions:**Supports:...

But a structured PEI-sheet gives a perfect look for the outer surfaces.Layer height: 0,2mmInfill: 25%Perimeters: 3Brim: noSupport: no, only for Wing_1 Additional information:Required filament quantity: ~1250gTotal print time: ~138hFull size:...

Without Card Tray lids you can get this printed with less than one 1kg roll of filament. Need the organizer for Base & Expedition {starting from scratch}: - Print one copy of all the files from this project - Go to Unserfamily's page and...

Though note that I print with 3D850 filament so hot water actually makes it stiffer after that How I Designed This Design principles Well, it had to be working chain, not some toy. Some could think its a bit OTT but this is to avoid creep in...

I hope PLA can withstand it. Now Next Level Racing has announced F-GT LITE cockpit and I'm considering to order one, I'll just wait for a few reviews. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't Matter Supports: Doesn't...

Just make sure the linear bearings are in the correct holes to run on the rods as their are positions for four bearings. Shopping List:M3 bolts of various sizes (exact sizes aren't very important).M3 hex nuts2x threaded rods and nut pairs from 3D...

If you have the proper filament colors, no painting is needed. The assembled model is 198mm tall.. Enjoy! ........................................................................................................... Special shoutout to maker Benoît...

They may work on filament printers, but we do not support that printing method as standard. STLs are provided in both pre-supported and unsupported forms. We suggest you download the free sampler pack to familiarise yourself with our formats and...

I power it with a 2 Amp USB power supply. Read the Gyrotourbillon Build Notes PDF in the files for more information. Enjoy, McMaven Print Settings Printer Brand: Prusa Printer: i3 MK3Rafts: No Supports: YesResolution: 1.5mm Infill: 20% Filament:...

Finally, it'll have you switch one final time back to Silver to complete the print. You can answer the prompt on the printer (was filament change successful?) with “no” to have the printer do an extra purge for you between colours, which is...

I have 14 other iris boxes designs and I have an instructable describing them and how to print them.Box StylesThere are a few decorative styles for the components: 2 stands 2 bases 2 collars 2 gears 4 top door patternsBeware...

But I strongly believe, this document would be a better guide to who wants to understand the design process of a small (light) weapon system.INTRODUCTIONAccording to history of mankind and warfare, the definition of firing arms were always varied by...

I will be adding a printing guide for each of the pieces as this becomes more complex. I have oriented the pieces as to how to print. Screws are properly oriented so as not to break. I use tree supports on the screws and QC that have knobs. All...

While many of these designs have had more detailed blueprints or 3d models made over the year, Art and I have attempted to take a fresh attempt at rendering these ships using only the original side profile artwork as a guide. ...

Or: This is a guide to create a straightforward contra-bass stand, which is based on a design from the online resource at http://www.kontrabass-atelier.de/zubehoer_e.html#stand. Or: A simple contrabass stand can be constructed following the...

If so, we recommend checking out [this excellent guide](https://learn.adafruit.com/adafruit-proto-screw-shield). Once everything is soldered, it's time to test it works. Please use this diagram as a reference: ...

If using foam please test these techniques carefully as this guide is mean for a wooden bat. For example foam might get eaten by paint thinner, and you should not use fire on foam etc..Distress the bat, beat it up, burn it sand it, dent it...

Use instructions from the 3.1 build guide. 39. [optional] Stick 40mm heatsinks onto each XY motor. 40. [optional] Install M6x10mm button head bolts onto each motor fan mounts, and 3030 M6 T-nuts onto the bolts, do not tighten them yet. 41. Do not...

Controlled by captive artificial consciousness, the ancient elevated monorails guide the cargos of death down deeper and deeper into the wastes of the underlevels to be unloaded and injected deep into the undergrounds. Far and away from the upscale...

The wires of the LED's are guided inside of the T-slot of the vertical aluminium profile and conducted through the designated opening inside of the electronics case. A reflective screen / Light shield on the light bar can be attached if required. See...

You can probably survive without.) The obvious allen keys are also needed. Instructions are currently in the form of PDF drawings and an extensive video guide. All the video links are down below. Some show some information about the design process,...

Select the two hexagons as the two profiles and in the guide curve section, select each arc created.It should look like this:Next create the part where the handle will connect. Create a new plane 5.5 cm away from the top plane. On that plane create...