solidworks test questions 3d models

Make sure to test the right direction before forcing the magnet into its hole .... How I Designed This Changes to the code. I took the code from Daizyu and came up with 2-3 interesting configurations that required some change in the code. E.g. ...the...

Slightly enlarged the pin hole and removed the wider section of the hinge for esthetical reasons (Probably didn't need to be widened to begin with)I've also noticed during the additional test printing that the latch doesn't snap shut the two halves...

You can pay with PayPal or your credit card.Watch the tutorial on how to assemble Hammerhead Corvette 3D Printing Model at Gambody YouTube channel.Also, you may like other Star Wars 3D Printing Models._______FAQ: Where can I print a model if I have...

An easier test would be to hold your wet finger tip to the (cold!!!) nozzle while the part cooling fan is running (gcode: M106 S255). You will clearly feel the airflow cooling your finger. [Again, don't do this while the nozzle is hot, you will burn...

Light Gray is next to White) See picture attached for correct wiring If you like, like this thing; it help my stats ;) Please post a picture of your nice setup and a comment If you love my designs, you may also consider tipping me, it helps me a...

Testing it I used the AIL and ELE channels. On my DX8 the mixing looks like this: ELE > AIL RATE: 100% 100% OFFSET: 0% TRIM :INH SW:ON AIL > ELE RATE: -100% -100% OFFSET: 0% TRIM :INH SW:ON If the...

After several tests I found the solution! The frame part now fits very tightly onto the frame and the elongated wall prevents it from tilting. Also added a M3 bolt hole at the back so that you can even use a T-nut to bolt the frame part to the frame...

Made in spaceclaim, tested in the manufacture of the master model of the product. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the models on screens with stl or obj files,...

Or if you know how to use CAD software, download the STEP file and design your own.There areFitting bases optimised for printing on their side, suitable for hooks and other flat fittings:KYZ-V1 - 1 cell highKYZ-V2 - 2 cells highFitting bases...

Go to the Source Files tab, select the file and click the Print with 3DHubs or Print with Treatstock button. This model was tested in Cura 2.3.1. To avoid printing problems, we recommend the following settings:QualityLayer Height: 0.1 mmInitial Layer...

Made in spaceclaim, tested in the manufacture of the master model of the product. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the models on screens with stl or obj files,...

I was test fitting a lot, so I didn't want something as strong as epoxy (and I didn't have any on hand) but if I was to make this again, I would probably go with a thin epoxy. - Add shaft sections one at a time, adding glue, aligning and letting...

I have put all the parts together & tested the laser, but have not put it into operation yet. For the electronics, I am currently running grbl firmware on a keyestudio CNC shiled V4 with a raspberry pi 3b Plus connected to it running v1pi...

Select the files you want to 3D print and click the Print with 3DHubs or Print with Treatstock buttons. This model was tested in Cura 2.3.1. To avoid printing problems, we recommend the following settings:QualityLayer Height: 0.1 mmInitial Layer...

It's still experimental and is glitchy, but I have had good success with it: whenever it generates messed up structures I just move the model and then moved it back and get it to regenerate.\r\n\r\nIf you're not using soluble supports, I'd recommend...

*** ************************************************************************************************** I found that the belt grooves printed best when they were laying down parallel to the build plate but I included a small test block with the same...

Select the STL file you want to 3D print and click the Print with 3DHubs or Print with Treatstock button.This model was tested in Cura 2.3.1. To avoid printing problems, we recommend the following settings:QualityLayer Height: 0.1 mmInitial Layer...

Made in solidmade, tested in the manufacture of the master model of the product. Saving stl & obj files occurs at the average values of polygons. This is usually enough to print a model in a 3D printer, but it may not be enough when producing a...

I'll eventually adapt the changes to the other STLs and formats once I get more testing completed. [ x ] 35mm front mount updates [ x ] 30mm front mount updates [ x ] 25mm front mount updates [ x ] 20mm front mount updates [ x ] 15mm retraction...

...If this is the case, and accuracy is important, you should scale up the dimensions a little bit to compensate. I only tested this for small gaskets. ...If the model proves unpractical for larger gaskets, contact me and I'll see how I can improve it.

In my case, I gain about 18mm more print area to the left.Edit (16.5.2024):After some testing, I recommend using the adapter with the BLTouch attached to the left side, as it won't get disturbed by the magnetic field of the stepper motor. Now it...

... Here is a link to that project:https://community.element14.com/challenges-projects/project14/attackofthedrones/b/blog/posts/srd-1---3d-printed-drone-arduino-raspberry---june-11th-update---it-fliesThe only thing now left is to test out the gimbal.

I have not printed/tested these myself - I will remove this note when I get confirmation that everything fits correctly. lrs-350_foldingCover_front_blank.stl this one is completely blank, you can add whatever cutouts you need for components of your...

I also reshaped the air ducts to be larger and less focused on the nozzle (more like those on the stock Ultimaker 2 fan mount), and changed the screw holes to use the screws that came with the Ultimaker 2.\n\nBefore uploading, I tested the fan mount...

In my tests the PLA version appeared to work fine so PETG may only be required for extra longevity. The 3D printed decals were printed at 0.1 resolution @100% infill to provide some visual density in a fairly thin component. Decal layer thickness is...

don't have one to test with. Part Cooling / Hotend Cooling - Upgrade "Kit" Very lightweight --- Original steel fan support and part cooling duct - around 50 grams --- Upgrade Kit (all parts plus extra bits) - around 15 grams Airflow is better...

Important Note: Direct translation of V-Ray Material settings may not carryover directly to other export formats supported by this asset; therefore it is advisable to keep results generated using this asset as the baseline and perform tests before...

NOTA: Part I below After having see the video from Stefan CNC Kitchen Here below https://www.cnckitchen.com/blog/testing-the-strength-of-3d-prints-re-melted-in-salt Also he did a re sintering in plaster in an early attempt, another did a previous...

I included the original and unmodified bolt for simplicity. The follwing spools are available for MasterSpool upcycling andare tested to work with MasterSpool-refills from DAS Filament: Tiertime/Cetus/UP Fila 700g Spools Verbatim 1kg Spools How-tos...

I did a test of taking the new cap on and off about 200 times and after the first few, it didn't seem to develop any additional slop. I wanted a bunch of spare hobby knife handles to distribute through the various places in my shop, but none of the...