sp360 3d models
21 3d models found related to sp360.thingiverse
it was Fixed from source now it is able to use with sp360 Please check with Picture
thingiverse
This is a 90 degree tripod adapter made for the Kodak SP360 spherical camera. I didn't like the fact that you couldn't mount it in vertical mode on a tripod so I went ahead and made an adapter complete with a place to put a 1/4 inch nut in to connect...
thingiverse
Lens cap for the Kodak SP360 Spherical camera housing whose dome is about 42mm. The camera lens screw-on protector is slightly smaller, maybe by 1 or 2 mm, so scale this down 97% for use directly on the camera. (Therefore it follows that a lens...
thingiverse
This is just a simple adapter for connecting a Kodak Pixpro SP360 or SP360 4K to various GoPro compatible accessoires Print Settings Printer: Prusa i3 (chinese make) Supports: Doesn't Matter Notes: Rotate the design 90 degrees on its side to get a...
thingiverse
This piece is designed to mount four Kodak SP360 4k cameras turn that into a stereoscopic 360 video capture setup. You need four 1/4-20 standard screws to mount the cameras and another 1/4-20 nut if you want to mount it to a tripod. By using...
cgtrader
⢠It is the high-quality low-poly 3D model Kodak Pixpro SP360 used in various fields 3D Graphics such as: game development, advertising, interior design, motion picture art, visualization, etc.. Modeling was made by ortho-photos of real action...
thingiverse
VR Mount for Kodak Pixpro SP360 4k foe included in package selfie stick. ... I used two conversed to 1/4 inch 20unc thread M6 nuts.
thingiverse
This adapter lets you use your Kodak PixPro with GoPro Mounts or vise versa. ...Print Settings Printer: M3D Rafts: Doesn't Matter Supports: No Notes: I needed a adapter to attach my Kodak PixPro sp360 to GoPro mounts, so i made one.
thingiverse
The adapter will snap in to the gimbal followed by the SP360 camera adapter which is held in with the stock GP (Green) Clip. I added 14g counterweight to balance the SP360 in the gimbal. IMPORTANT NOTE! You must hold the Camera at the 90 degree...
thingiverse
Side-by-side stereoscopic mount for a pair of Kodak Pixpro SP360 4K cameras. The interocular separation distance is adjustable between ~60mm and ~80mm. Cameras can be mounted directly onto the flat plate, or mounted with the second part, which...
cgtrader
It is the quality low-poly 3D model Kodak Pixpro SP360 4K used in various fields 3D Graphics such as: game development, advertising, interior design, motion picture art, visualization, etc.. Modeling was made by ortho-photos of real camera that is...
thingiverse
Simple 1/4" tripod/monopod mount adapter... ...it slot fits onto the existing Dual Camera Base Mount and latching mechanism.
cults3d
Simple 1/4" tripod/monopod mount adapter... ...it slot fits onto the existing Dual Camera Base Mount and latching mechanism.
thingiverse
This Camera holder give you the ability to connect a power bank to the cameras and with it extend the battery life of pixpros.
thingiverse
This is a remix of: http://www.thingiverse.com/thing:92014 I redesigned the adapter plate with screw pattern for the DJI Phantom 2. It's otherwise, the same deal. I use this with my dual Kodak SP-360s. It's a bit shaky for me. I should try...
thingiverse
Mount point for a Kodak pix Pro sp360 used the black version yellow version may be diffrent
thingiverse
Print Settings Printer: Da Vinci 1.0 Rafts: No Supports: No Resolution: 200 Microns Infill: 30% Post-Printing Parts Needed (Aside from a KODAK SP360 or SP360-4K) 4x #8 Sheet Metal Screws 4x #8 Washers 1x Standard Rubber Band 4x #6 Machine Screws 12x...
thingiverse
Something I whipped up to mount a Kodak SP360 4K to the underside of my 3DR Solo. This probably won't clear the stock gimbal, but I'm not sure since I don't have one. ... You will need 4 anti-vibration mounts.