spektrum dx9 case 3d models

Mount the Spektrum FPV monitor directly onto your DX9 transmitter for an enhanced flying experience.

Hallo, hier ein einfacher Knüppelschutz für die Spektrum DX9 um den Sender in einer Tasche zu verstauen. ... Grüße, Bernhard http://youtube.com/channel/UCuGMUCh7iKq4J6Uhd_ZcNQg

... for Spektrum Radios. ...Compatible with DX9, DX8, and Other DX Series Models. 11-26-2017: Revised Version 6 Ensures Proper Alignment of Saver and Lanyard Clasp. All Gimbal Protectors Are Now Printed Using High-Quality TPU Material. ...1-23-2020

This is a high-gain antenna adapter cap designed for the Spektrum DX9 radio, offering an alternative modification option.\r\n\r\nOption 1 - Single Antenna Configuration\r\nThe adapter features one SMA connector and a second "blind" SMA connector for...

I decided to create my own gimbal stick protector for the Spektrum DX9 since there aren't many options available. This design might work with other Spektrum radios, but I don't have any other models to test it on. To ensure a proper fit, you can...

This durable guard features a sleek design that fits seamlessly onto your DJI DX9 controller. With its sturdy construction, it can withstand impacts with confidence, giving you peace of mind while flying. Installation is easy, requiring no tools or...

I'm installing a new wall mount that's significantly slimmer than my previous design, mainly because the DX9 Transmitter handle has a notably narrower profile. ...The print job turned out perfectly after printing upright with a 0.3 layer thickness.

A compact TBS Crossfire mounting system designed to seamlessly integrate with the Spektrum DX9 transmitter handle.

It's a replacement antenna cover for a Spektrum DX9 Radio. Normally, the antenna cap attaches with 2 screws and 3 plastic clips. If you snap off the clips from opening the case too many times, it will become shaky. I used precise measurements and...

Replication of the Spektrum DX9 - RC Radio Transmitter. Printing at a 45-degree angle is highly recommended, along with the use of a support structure to ensure stability during the printing process. ... I recently utilized the powerful tool known as...

... my laser cutter. This cost-effective solution was significantly cheaper than the $14 option available on Amazon. Note: The photo shows a coupon sheet that I cut out on my laser cutter to demonstrate that the profile fits the screen of the Dx9.

The current design has a tendency to topple when the DragonLink is mounted on its back, causing the DX9 to fall over. To address this issue, I've added a port where you can plug in the female end to keep it flush with the rest of the device. ...It's not...

It can be used with: Antenna cover with pigtail location for Spektrum DX9 (single antenna) - http://www.thingiverse.com/thing:1592674 Antenna cover with 2 pigtail locations for Spektrum DX9 (twin antenna) - http://www.thingiverse.com/thing:1592720...

Have been using the **IISI Cockpit V2** telemetry for RC plane flying for a while now with my **Spektrum DX9** transmitter. While I was very happy with the hardware itself, so far, I've always had to attach the Cockpit to my Tx using velcro - not...

Exceptional DX9 Mount for TBS Crossfire - a seamless fit that exceeds expectations.

Remix of DX8 Gimbal Stick Saver from DavidCanfield Now perfectly matches the DX9 Gen2 Black Edition. ...It will likely fit other DX9 G2 transmitters as well, although I haven't had a chance to test it yet.

I designed a custom adapter for my DX9 to give it a sleeker appearance, hiding the cluttered accessory port where I routed the wires for my TBS Crossfire setup. ...This project requires printing with flexible materials such as TPU to ensure a secure fit...

Set of x2 Throttle Limiting Wedges for a Spektrum DX-9 - These parts are Not Available from Horizon Hobby. I've printed and tested them, and they fit perfectly, preventing warping. With PLA, a 65-degree bed was the key to success. I've installed...

Connecting protective covers to a gimbal requires securing them to the Spektrum Radio DX9 via the sebsx system.

This mount aims to fulfill several objectives: 1) It positions the EZUHF antenna at a different angle than DX9's 2.4 GHz antennas, 2) it minimizes interference between EzUHF's 70cm and DX9's signals, 3) offers maximum cooling for both transmitters,...

this is a remix

You can install one or two boosters on it, and use it with: Antenna covers featuring pigtail locations for Spektrum DX9 (single antenna) - http://www.thingiverse.com/thing:1592674 Antenna covers with 2 pigtail locations for Spektrum DX9 (twin...

... Assembly instructions can be found at http://www.canardwifi.com/2016/05/27/augmenter-la-portee-dune-radiocommande-2-4-ghz-exemple-dune-spektrum-dx9/. For those who don't speak French, Google Translate is available to help decipher the instructions.

I designed a customized battery cover and battery holder specifically for my DX9 transmitter, allowing me to safely store and utilize a Tattu 3S 850mah 45C battery while using the TBS Crossfire system.

The DX9 transmitter has an uncommon rear mounting bar which doesn't currently fit many of the existing adapters for the long range transmitter modules. ...Using just some 3/4" aluminum bars, velcro and sticky foam, you can create an adapter that keeps...

The DX9 transmitter boasts a unique rear mounting bar that falls short in compatibility with many current adapters designed for long-range transmitter modules. ...To circumvent this issue, simply utilize 3/4" aluminum bars, paired with velcro and sticky...

My first design antenna cap broke after a few years, so I designed an updated version. ...

After many iteration of the original design I am quite satisfied with this one. Tried to selle printed version on ebay but now I rather post it here and count on some donations to finance my printing material needs. ... I hop you will enjoy this...

My first design antenna cap broke after a few years, so I designed an updated version.