spongebob 3d model

My O scale model train layout represents the section of the Pittsburgh & Lake Erie Railroad between McKees Rocks and Youngstown. This wall section (stretcher bond brick pattern) will let you assemble a background flat of the McKees Rocks...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

This model currently comes in 4 variations. Standard rail facing forward. Standard rail angled 5 degrees to the side off the rail. Standard rail with sidekicks facing forward. Standard rail with sidekicks angled 5 degrees to the side off the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

Now, everything will just fit without removing the box insert.ModelQtyDescriptionquacks-chip-box.stl2Boxes for Red, Green, Blue, and Yellow ingredientsquacks-chip-lid.stl2Lids for those boxesquacks-misc-box.stl1Box for the miscellaneous ingredients...

Please note that this model doesn't include the hooks on the bottom for the external antenna coupling. My car doesn't have one but I think it can be added easily. You can find the assembly instructions in the print instructions or here at...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 45...

This is the first 3-D model I have built from scratch and I was looking to get it done quickly. So, I kept it simple but did note that it wouldn't take much to add a few more amenities that would suit personal needs or desires. The router fits...

These two parts are rather small but also simple ball joint parts that rely on friction and cannot be tightened. For those of you that want a to be able to tightly secure your camera in a certain position, there are also parts that form a double-ball...

I RECOMMEND THIS ONE INSTEAD:https://www.printables.com/model/169138-prusa-mini-detachable-cooling-duct-assembly-v2 About this modI have never been happy (okay that's a lie, I was happy for the first few weeks) with my Prusa Mini's cooling. This is...

I'm not sure how common this exact failure is but I figured I'd share it in case it helps someone from throwing out their cover and having to shell out for a replacement. There are other repair pieces for Audi/VW cargo covers which are used on wagon...

If you look at the print of the base (or the model of the legs) you will see there is a round hole with three slots surrounding it. These slots fit a specialized washer that is used in the vise to keep the base from rotating when it has been...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_bottom_fillet_resolution = 8...

After sanding the putty flat, paint it using model paint or cover it with a large sticker to conceal any imperfections. Test fit the Laforge diversity module into the hole where the old receiver used to be. Cut off this standoff because it's...

For your Rubik's cube to keep the fluidity of its movements, it is necessary that the dimensions of the model are reproduced very precisely, and that your board can allow a first layer of 0.1 mm... Usually to deal with defects in the...

(I used bodies instead of components to avoid model breakage in case of major size change.) Required Parts list and where I got them: 1X 2032 battery holders: https://www.amazon.ca/gp/product/B08SQRSTJ4 1X rechargeable LIR2032:...

...All "mandatory" supports are already in the model. This piece on the photos was accidentally done with 0.15mm layer height and it turned out fine, although I intended to print it with 0.08mm height. Everything from 0.1mm and below should be alright.

Assembly Video: https://youtu.be/GqohsdSTQrc Using"2mm Male Female Banana Plug Connector for RC Model ESC Motor Speaker" to convert Foster Connectors to electrical connectors -concentric BNC like. The printed parts hold these 2mm contacts in place...

Thus I found my way to thingiverse and sought for every model that was irregular eventually finding some customizable builders. While the brick making one is heavy, beam kind was cool, but limited to either halfheight simple or up to # shape with...

The extra space available in a Volcano setup would allow much more open channels and sweeping paths, and I would like to improve the Volcano version in future, but this will require significant modelling work which I just don't have time for at the...

(Not required for revision 2) Scaling: The model as is in the STLs will accommodate most types of earbuds, however it can be scaled down as much as 30-35% for smaller sets. If you use earbuds with an inline control, such as the ones shown in the...

Then, once the mount is installed on the handle, you can unscrew the bolt and increase the distance from the magnit to the sensor, increasing it enough so that the brake sensor only activates when the brake is actually applied.The model is made in...

You could group them in Tinker and make a single/twin mega model - love that Tinker feature! Support is required in places due to geometry, but it's very simple square profile support that is easily removed. I always try to avoid it, but not at the...

It's just a model I whipped up, and sliced it with a bunch of retraction changes. Then went back and spliced all the g-codes together. Base Cura profiles I use: layer height - 0.2mm Optimize wall print order (do not retract before outer wall), print...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

**HOW I PRINT MUCH QUICKER WITH STOCK HARDWARE** -------------------------------------------------------------------------------------- Here are the two videos that give details on how I print much faster with stock hardware (changes to slicer...