spool clamps 3d models
97845 3d models found related to spool clamps.thingiverse
This is a simple spool clamp with a built in knob instead of relying on a wing nut. I use these daily as a luthier, especially on violins but they can be used for almost anything. The 1/4"x20 hex nut should be glued in with cyanoacrylate if possible....
thingiverse
Spool clamps are used by luthiers to build violins and other stringed instruments. Typically they're made from a hardwood dowel with a threaded rod trilled through the center, with cork or leather lining the jaws. They're great for clamping the edge...
thingiverse
... the clamp, print 2 of them to completely box the filament in like the photos. The clamps can move side to side to allow the spool to move free and easily. ... I will upload thicker models if requested, alternatively they can be easily modified.
thingiverse
A simple spool clamp for Qidi Tech XMAX or XPLUS spool holder(30mm diameter).
thingiverse
# Print Details **Printer :** * Creality Ender 3 Pro(2019 Q3) * BlTouch bed leveling **Material :** * Sunlu PETG * white * 1.75mm * 235C / 75C **Set Up :** * 0.6 nozzle * glass bed * printer is located in an insulated enclosure **Settings :** *...
thingiverse
I kept finding as i bought different filaments that the spool clamp size was never right! Very frustrating they dont all keep them the same size! Created for my Ender5 but i believe the spool holders is exactly the same on the 3 so should work -...
thingiverse
This is a clamp-on spool hanger for great big spools. ... I use it for the large rolls from coexllc.com
grabcad
This is a simple clamp to hold my filament spool in place on a aluminium rod with adiameter of 12mm on my Geeetech Prusa I3 pro.I use the 3d printed 'GEEETech i3 Filament Spool Holder' by ali55 on thingiverse which works fine for me.
thingiverse
This is a simple clamp to hold my filament spool in place on a aluminium rod with a diameter of 12mm on my Geeetech Prusa I3 pro. ...I use the 3d printed 'GEEETech i3 Filament Spool Holder' by ali55 which works fine for me.
myminifactory
This is a simple clamp to hold my filament spool in place on a aluminium rod with a diameter of 12mm on my Geeetech Prusa I3 pro. ...I use the 3d printed 'GEEETech i3 Filament Spool Holder' by ali55 which works fine for me.
thingiverse
(3.8 seems to be the travel each way) Then you slide the clamp on over the wound spool keeping the winds in place. Next you put the roller in the middle of its travel (approx 9.5" from bottom of end stop bracket) and put a ziptie under the roller...
thingiverse
Prusa's base spool holder has much space to filaments, you can use this clamp to restrict unwanted movements of filament cartridge. I've designed it because of failed print by new filament rolls wrong and filament mess. You can use filament guide to...
thingiverse
a spool holder for ikea lack that reuses the ender 3 spool holder. ...also some mounting tape
thingiverse
remix from D_jespersen just an extended tab to stop the spool. ...i have a centering for my spools and was worried it wouldn't stop it. printed it with 0.8 nozzle 0.4 layer height. ...not the prettiest, but that doesn't matter.
thingiverse
to hold your spool in place. let me know if you want another with. ... If you like my design feel free to tip my design https://www.paypal.me/Djdenzo
cults3d
to hold your spool in place. let me know if you want another with. ... If you like my design feel free to tip my design https://www.paypal.me/Djdenzo
thingiverse
... and fully parametric. Instructions Choose some values in the "User-defined values" section if necessary, render, and print. The default values fit a typical wire spool found at Radio Shack.
thingiverse
This is my design of a spoolclamp for my "Ender 5" that the spool doesn't move anymore. ... Inner diameter: 30mm Hight: 20mm 195°C Hotend 60°C Heatetbed - Glassbed from creality 50mm/s Printspeed 25mm/s Outer wall printspeed About 20 minutes...
thingiverse
I designed this from the bottom up because it's dead simple but Captaingrey inspired this way of doing it. They're 1.5" in diameter for extra beef factor. I know part of the original point was that it wasn't using wing nuts but I liked the...
thingiverse
For FRC4905 new hardware cart, these wire clamps allow one to hang a 1/2 PVC pipe from the rack to support various wire spools. They work like a cham and the PVC pipe gently clicks into place for easy removal and installation of spools. Each clamp...
thingiverse
(There is no text on the parts!) Inserted the Spool Clamp due to comments within other variations of the Spool Rollers having issues with the Spool falling off. Requires: 1 Print for the Spool Clamp 2 Prints for the Spool Holders Total of 2 bearings...
thingiverse
A simple clamp to prevent the spool from moving on the holder
thingiverse
I printed this Ender 3 Filament Spool Holder Adapter https://www.thingiverse.com/thing:3421762 It was a bit short, and needed a spacer. ...spacer is thinned down to 10.2mm
thingiverse
For one spool clamp you need following parts: Print: 1x "Filamenthalter Unterteil.stl" 1x "Filamenthalter Deckel.stl" 3x Filamenthalter Druckstück.stl" Buy: 3x Spring 0,5x4,5x12mm 1x Bearing 608ZZ (8x22x7mm) I used these springs:...
thingiverse
This is a spool clamp for Vik's 500m PLA spools Instructions You need the following parts Printed 4 SpoolClamp.stl from Greg Frost https://github.com/GregFrost/PrusaMendel/blob/master/spool-clamp.scad 2 Vik500mSpoolClamp.stl Vitamins 4 155mm M8 rod 2...
prusaprinters
This is a spool clamp for Vik's 500m PLA spools Print instructionsInstructions You need the following parts Printed 4 SpoolClamp.stl from Greg Frost https://github.com/GregFrost/PrusaMendel/blob/master/spool-clamp.scad 2 Vik500mSpoolClamp.stl...
thingiverse
This is an alternative method to lock your spool in place. I was getting fed up of tediously winding 2 nuts on and off the bolt everytime I changed the reel. To use, just pinch the handle, slide along bolt so it buts up against the bearing, then...
myminifactory
... Nerds Spool Holder Competition. ... It is a spool filament holder that clamps on a 1.5" x .75" board. I have printed this in PLA and PETG. I like the PETG version better because it is more flexible and less brittle. ...ABS and Nylon should also work.
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=589518 Instructions Using the following options: lip_height = 2 spool_radius = 7 lip_radius = 9 $fn = 70 spool_height = 30 spindle_radius = 3