ssd 2.5 inch 3d models

A simple 2.5 inch HDD/SSD enclosure

http://www.thingiverse.com/apps/customizer/run?thing_id=384919 Instructions Using the following options: lidInsetOffset = 0.0 coverThickness = 1.0 lidInsetHeight = 4 tabSize = 1 interiorFillet = 2.0 hingeFillet = 3 interiorHeight = 11...

Required parts: - mSATA to SATA adapter like here: https://www.aliexpress.com/item/2017-Universal-mSATA-SSD-To-2-5-Inch-SATA-6-0-Gps-Adapter-Converter-Card-High/32613616694.html - 2x screws M2x5.5 (or M2x6) (eg. ...from an old laptop enclosure) - 2x...

This is a tray to fit 2.5 inch SSD drives into the 3.5 inch Dell's server slots.

This is the same tray that comes with QNAP NAS devices. ...This part fits the 2.5 inch SSD and HDD drives into the 3.5 inch slot.

I had useless mSATA SSD. ...Bought an adapter on ebay for it http://www.ebay.com/itm/201336720279 This thing is an adapter for 2.5 inch HDD size. ...So basically is adapter for adapter :)

Bought an adapter on ebay for it http://www.ebay.com/itm/201336720279 This thing is an adapter for 2.5 inch HDD size. ...So basically is adapter for adapter :) Print Settings Printer: Ord bot Hadron ...

Here is a simple design to hold a 2.5'' SSD drive below a Raspberry Pi 4 Coupe Case. In order for the Pi to have air flow, the SSD is held away from the base. This was designed to be used with a Pi running Home Assistant, replacing the SD card with...

Model of standard size 2.5 inch SSD hard drive with accurate mounting screw position and sizes.

This is a triple 2.5 inch SSD holder for desk use. The sizes of the holders may not fit your personal needs. Just drop it onto your designing software and resize them. ...Hope that this helps you out

Just a quick and dirty sled (mount, adapter) for 2,5 inch SDD to mount in 3,5 inch PC case disk bay. You can sightly shrink side holes in order to tap them. I have a quick mount system in my PC case, so hadn't need threads. ... Designed in Fusion 360 -...

This is a rack that I designed because I wanted a large external storage and had a few 2.5 inch hdd's laying around. I did a little amazon shopping and bought a couple SATA to USB cables so I can connect them to the computer. ...Hope this model is of...

Quickly added some "speed holes" to improve airflow in the enclosure I'm putting this in as a blank to fill an empty SSD spot. Holes added by subtracting a couple cubes from the original model in Microsoft Builder. ...Eyed them in the center somewhat,...

Quickly added some "speed holes" to improve airflow in the enclosure I'm putting this in as a blank to fill an empty SSD spot. Holes added by subtracting a couple cubes from the original model in Microsoft Builder. ...Eyed them in the center somewhat,...

http://www.thingiverse.com/apps/customizer/run?thing_id=446851 you will need to scale it up by 3% Instructions Using the following options: battery_number = 8 battery_depth = 10 tray_depth = 2 base_thickness = 4 battery_height = 45 gap = 2...

HDD/SSD wall mount with air flow holes. ... Print with supports, 100% infill. 2 versions - 3 and 4 holes for screws

This is an adapter for 2.5 inch hard drives or SSDs in a Cooler Master tower. My case came with one, but I recently replaced some mechanical hard drives with SSDs, and I needed more. ... This is basically a copy of the one provided, minus any holes in...

A multi and a single case for safeguarding 2.5 inches hdd and SSD disks. There are 2 3d models, one for single disk carrying and one that can hold up to 3 disks. ...The 3d models have to be printed twice to make a whole case.

I made this case to fit my 2.5" Hard Drive, but it should also work great for 2.5" SSDs as well. The case fits snugly and the top does not come off on its own. ...The hole for the SATA to USB cable should be big enough for most cables, but may need a...

adapter from 2,5 inch SSD to 3,5 inch

This is a small ssd holder. I made a design on it, where it says in Russian letters "Mom, this is for study." There is a version without design. ... The distance between the holes to make sure it will fit you are shown in the photo.

This is a 2.5 inch SSD spacer with dimension 100 x 70 x 2.5 mm. I designed this part for replacing a spinning disk with SSD in my iMac. ... You should use PETG or ABS because it might be warm when in use.

Remix of 2.5 Inch SSD-HDD Rack Legs added

A cover and a mount plate.** **The mount plate holds the 2.5 inch disk, the Raspberry PI and the cover together.** **The 2.5 inch disk also acts as the base for your NAS.** **You can connect the SSD with a USB to SATA adapter.** **This Raspberry Pi...

This is a remix of 2.5 Inch SSD-HDD Rack by Gunnthorian August 10, 2017 This rack is a holder for 2,5" HDD and SDD I tried to dispence the supports and I have added the tabs of the Remix of " Shorter rack by kpsyrstad August 02, 2020 I changed the...

This holder is designed for two 2.5 inch SSDs in place of a single HDD. There are no screw holes for SDDs, they will slide in and out freely. It is not really designed for 2.5inch HDDs because there is no way to dampen the vibration from them. ...Print...

I was looking back at my old designs, and saw an SSD mount I had made. I was inspired to go back and make one that works with metric screws (M3x5mm) and that uses much less material. ...I haven't actually printed it yet, so try it and let me know how it...

This one is for 2.5" HDDs and SSDs. Now you can build some ridiculously powerful SSD array or a small NAS, whatever you all may need this for. If you don't have a 3D printer and would like one or more of these you can always find me on 3D...

Spacer block to prevent a 9.5mm or 7.0mm height 2.5 inch disk from moving around too much.

This design is an attempt of converting mounting holes of 2.5 inch disk drive to 3.5 inch form factor. The SATA interface port should remain in the same place which is useful for upgrading your old ALL in One PC with a SATA port connector fixed. ...