stand off mounts 3d models
590058 3d models found related to stand off mounts.pinshape
The stand-off mount allows for designs with limited internal space. The port allows access to the coupler. ...Print time is about 5hrs with 0.25mm layer height.
thingiverse
This is a stand off for mounting my Ender 3 v2's power supply on the underside of my Ikea Lack enclosure. Print two PSU Secures to the mounts with 4 m3x8 cap screw. The mount then is secured to the enclosure by some screws I found in my garage. The...
prusaprinters
This is a stand off for mounting my Ender 3 v2's power supply on the underside of my Ikea Lack enclosure.Print twoPSU Secures to the mounts with 4 m3x8 cap screw. The mount then is secured to the enclosure by some screws I found in my garage. ...The...
thingiverse
Shortly after printing my newly designed standoff, i realized there was no way i was going to get all 4 mounting brackets to line up with the wood lathe, so i designed an opposing side for my standoff to act like a clamp, allowing me to use machine...
thingiverse
Crossfire Antenna Mount. Made for marotte but will work on others. ...Need to print 2.
thingiverse
There was no mount/holder that I could find for the Cinerat, so I designed this one. The holder is designed for the RDQ 880 GPS + Glonass. I know this is a rebranded item, so there are other companies that sell the same GPS unit with different...
thingiverse
These are some simple stand offs to mount a hard drive to a flat surface. ...Mounts use (6) #6 wood screws.
myminifactory
These are some simple stand offs to mount a hard drive to a flat surface. ...Mounts use (6) #6 wood screws.
cults3d
Here is a Nema 23 Stepper Motor Mount that I designed for use on a CNC Router/ Mill project I am working on. Open to feedback on print quality and tweaks. ...The one pictured was printed in ABS at 240 degrees with 0.2mm layer height.
thingiverse
Simple stand-off mount for a Parallel 5 axis CNC Breakout board. ... Elevated for extra isolation or run cables underneath it.
thingiverse
This is for a Eufy WIRED video doorbell, it has recessed mounting holes that fit a "standard" rectangular doorbell template and are the same height. There's a pass through hole for the wires and holes for the WIRED Eufy mounting plate. Print in...
thingiverse
This is a heavy stand-off motor mount with additional spacers. It designed for EP power setup on SIG Kadet Siniorita RC Plane but can be used for any 35-40 mm motor. Mount plate diameter is 55mm and stand-off total height is 30mm with additional...
thingiverse
Lets you quickly make mounting plates/stand offs for the various PCB's you have in your projects. Works with PCB that have a symmetrical mounting hole pattern. OpenSCAD Settings: All distance values in milimeters. ...use_cutout=true; resolution = 90;...
thingiverse
Bracket mount for the Azteeg x3 Pro... Several mounting holes. Fan is for a 92mm. Print Settings Printer: Cartesian Rafts: ...
thingiverse
Motherboard Stand Off Kit with SSD Mount for mining setup
thingiverse
I wanted to (a) mount the extruders vertically to make it easier to load filament, (b) raise the extruders up so they didn't interfere with the top of the build volume, and (c) add vibration isolation to the extruders. Credit for the inspiration...
thingiverse
Holds 3mm Antenna tubes. ...28mm spacing for quads. Designed to stack all together with a U.FL AXII, HellGate Buzzer and antenna tubes. Buy it here >>>>> https://www.wickedquads.com/collections/3d-printed/products/alien-antenna-tube-mount
thingiverse
13mm Soft Mount Flight Controller stand-offs. Print in 10% infill TPU. ...Cut to length.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=2083883 Instructions Using the following options: resolution = 90 spine_width = 20 depth = 36.5 mount_hole_diameter = 4 pillar_diameter = 6 pillar_height = 15 base_thickness = 4...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=2083883 Instructions Using the following options: pillar_diameter = 4.7 spine_width = 20 resolution = 90 base_thickness = 4 depth = 17 pillar_hole_diameter = 1.5 width = 31.2 pillar_height = 15...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=2083883 Instructions Using the following options: spine_width = 20 depth = 36.5 mount_hole_diameter = 4 base_thickness = 4 pillar_diameter = 4.7 width = 36.5 pillar_height = 15 resolution = 90...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=2083883 Instructions Using the following options: pillar_diameter = 6.5 pillar_height = 15 mount_hole_diameter = 4 width = 69 depth = 33 resolution = 90 base_thickness = 4 pillar_hole_diameter =...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=2083883 Instructions Using the following options: pillar_diameter = 4 pillar_height = 10 mount_hole_diameter = 2,5 width = 55 depth = 40 resolution = 100 base_thickness = 4 pillar_hole_diameter...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=2083883 Instructions Using the following options: resolution = 90 pillar_height = 15 depth = 33 base_thickness = 4 pillar_hole_diameter = 1.5 mount_hole_diameter = 4 pillar_diameter = 4 width =...
thingiverse
7cm by 3cm Whole Proof PCB mount with stand-offs. ... If you ever needed a way of securing your whole/proof PCB so it wont short or even attach it to a project this might be useful
thingiverse
Customized version of http://www.thingiverse.com/thing:2083883 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2083883
thingiverse
Customized version of http://www.thingiverse.com/thing:2083883 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2083883