standalone cr 10 3d models

CR-10 V2 Extruder Motor Knob for stock extruderIf you like it --> press like it :-)Remix of the "Creality Ender 3 / MicroSwiss Direct Drive Extruder Motor Knob" by un_ours_blanc.Had to scale it, but here you can download it directly in the scale...

... height regardless of which hotend you choose. But that's not all - I've also included a mounting point for your CR-10's stock probe, securing it to the same sturdy spot as the hotend mount. ...No support structures needed; print with confidence!

To achieve this, it's recommended to measure your CR-10's heatpad dimensions and make any necessary changes to the 'cr10jackplate.stl' file before printing. It's also suggested to print the aforementioned file in high-temperature materials such as...

Filament sensor mount for Creality CR-10, designed specifically for the type of filament sensor shown. Requires 2x M3 x 12mm screws and nuts. PTFE version available. <h1>Raspberry Pi Connection</h1> Connect to Raspberry Pi GPIO pins as follows: ...

The PTFE (Teflon) tube has a measurement of 78 mm in lengthAttached a basic model of the filament sensor.Adaptador para la impresora CR-10 v2 de Creality. Con él se convierte la impresora en "direct drive" eliminando el alimentador "Bowden" y...

BL Touch/3D Touch mount for a Creality CR-10 V2/V3 3D printer This mount attaches to the stock Creality x-gantry bracket on V2 and V3 printers using two M3 socket head cap screws. Any length screw greater than 6mm will work. This mount works well...

I have been using the magine That Titian/Atlas, Creality CR-10, Afinibot A31 Print Cooling https://www.thingiverse.com/thing:2274499 Dual Blower mount on my CR-10 with amazing results. It just bothered me that the right side wasn't securely attached...

I have been using the magine That Titian/Atlas, Creality CR-10, Afinibot A31 Print Cooling https://www.thingiverse.com/thing:2274499 Dual Blower mount on my CR-10 with great success. It just bothered me that the right side wasn't held to the metal...

This is primarily for the CR-10: to create some extra space between the bed platform and screw knobs, so print four of them for each corner. I had to use it after removing the foil/foam from mine while doing the following mod:...

Adaptador para la impresora CR-10 v2 de Creality. Con él se convierte la impresora en "direct drive" eliminando el alimentador "Bowden" y preparandola para filamentos flexibles tipo TPU o Filaflex. Diseñado para una impresión sin soportes. Son dos...

eSun PLA+ Filament: https://www.bastelgarage.ch/pla-filament-1-75mm-schwarz-1kg-esun Original Creality BL-Touch retrofit kit : https://www.bastelgarage.ch/cr-10-v2-bltouch-auto-bed-leveling-sensor For the do-it-yourself alternative you need the...

It was inspired by the CR-10 version: https://www.thingiverse.com/thing:2493628. Although I couldn't find it initially, I stumbled upon it later during one of my Thingiverse search sessions. I decided not to create a full cable chain, opting instead...

Use this insert to avoid unwanted pause of CR-10 V3 due to the missed detection of filament. Printing: No special requirement. Installation: Remove the four screws on the filament sensor. Insert the printed part into the lever of the...

... a rather thick outer shell (2.0 mm) and 40% infill. It's sturdy enough now. An advise: screw and / or glue the brackets to the table. My other design for the CR-10 (drawers underneath the printbed): https://www.thingiverse.com/thing:4974905

This is a re-ENHANCEMENT of: CR-10s S5 z axis stabilizer, Frame Braces by eckeSolutions https://www.thingiverse.com/thing:2747230 Additional Parts for Assembly: 2 off 100mm Long Threaded Stud Bar Rod @ 10mm Diameter [cut to desired length] 8 off M10...

This is a Y-Axis Mount and Cover for the CR-10 that cleans up the electronics, increases the adjustment range of the Y-Axis and is triggered by the bed frame instead of a V-roller. The forward position of the mounting screw allows for the sensor to...

...Radius on the base is hold the holder nice and tight on the case. Print Settings Printer Brand: Creality Printer: CR-10 Rafts: No Supports: No Resolution: 0,2 Infill: 20 Notes: wheel 0,1 holder 0,2 How I Designed This Category: 3D Printer Accessories

Coil holder designed specifically for the Creality CR-10 3D printer is a straightforward and easy-to-use accessory. Simply place it on top of the frame and secure it with two screws from below using a small plate. Inserting the roller through the...

This part was specifically designed for the CR-10 printer's older model. It replaces the stock Z motor tiny bracket that holds the motor in place from the side, but only partially since the motor still moves around due to lack of proper mounting from...

... out the entire section and it left a thin layer from the previous piece intact. https://www.thingiverse.com/thing:2246011 Print Settings: Printer: Creality CR-10 Rafts: Not necessary Supports: None required Resolution: 0.24mm Infill: 60% density

I made this replacement shroud for the Creality CR-10 Smart for a test fitting.It resembles the original shroud.You can either print only the Hotend-Shroud and leave it “naked” or print the decor piece in a different color as well and glue them...

I've created a custom leveling knob attachment for my CR-10 S4, and it's been a game-changer. I finally figured out what was causing the issue in my case - loose screws on the leveling knobs that kept shifting during long prints. ...To fix this problem,...

CR-10 Titan Aero Part Cooling Fan - Engineered with Fusion 360 \r\n\r\nBefore starting your print, verify that the mount orientation of your Titan Aero is correct, as some other models feature a reversed configuration. \r\n\r\nPrinting Settings: PLA,...

I downloaded and use the TUSH spool holder for my CR-10 control box, noticing that the filament rubbed against the edge of the box and was beginning to scrape away the paint. I quickly threw together a solution and it works surprisingly well. ...Whether...

This is a Sharpie holder that attaches to the cooling housing on a CR-10. It was built to practice writing G-code manually. It is built with magnets so it can pop off if the machine crashes. ...Notice in the video that the piece of paper has all of the...

I really appreciate your awesome CR-10 accessory Odinbear! I was determined to get the airways inside the vortex section of the fan shroud looking their absolute best. So, I tweaked the original design by splitting the vortex into two separate pieces...

Here's an adapter for mounting Tectink PLA filament spools directly onto your Creality CR-10's standard spool holder. To accommodate other printers or brands of filament, I've also included the Fusion 360 design files for making adjustments as...

I haven't spotted any rear y-axis pulley covers for the CR-10, so I whipped one up in Fusion 360. The part clips over the center section of the stepper motor from above. If it needs adjusting, let me know; revisions are being made, so keep an eye on...

I recently bought myself a CR-10 V3 and the first thing I noticed was the wires for the extruder will touch and drag on the hot bed and catch on the print. This was really not thought through on Creality's side. ...This is just a quick print that will...

To give my spool holder a sleek upgrade, I've integrated the threads from the longer spool holder into the parametric adapter, effectively eliminating the need for the original CR-10 spool holder that came with it. ...If you decide to print this design,...