standalone cr 10 3d models

The link is: https://zesty.tech/collections/the-nimble/products/cr-10-nimble-sidewinder This cable tray attaches securely to the X stepper frame and allows drive cables and wires to slide smoothly through it. The STL models for this cable tray have...

... and I've fixed that issue. Hope you enjoy it! And if you do, be sure to like this project! Thank you! S3D Profile: If you tried the G-code for the CR-10 and are interested in my profile, here it is available for download: http://vivads.net/Z7kXCqI

I recently upgraded to a DIY Magnetic Build Plate for the CR-10 (300x300) and I'm thoroughly impressed. Even after several months, my opinion remains unchanged - this mod has revolutionized my 3D printing experience. From now on, I won't use a 3D...

Nice small tool holder for all the standard tools that come with the CR-10 V3.Holes put on a 5 degree angle so the don't fall out.Designed it to mount on top op the frame bars.2nd version fits under the frame bars and is a bit longer (3.5mm) to...

The mod of my Scholle y motor brace was a necessity as it didn't fit my CR-10 S5 like it should have; 10 mm needed to be shaved off. I used two M4x10 screws and attached hammer nuts to secure everything on the CR10. Four M3x60 screws were necessary...

UPDATE 02/06/2019 SIGNIFICANT UPDATE X TENSIONER FOR CR-10 / CR-10S Mk7 VERSION The guide system has been upgraded and simplified, applying changes to all models. The dimensions of the screws have been unified across all versions. The minimum belt...

I liked it so much I wanted to use it on my CR-10S also, so I remixed this bed mount for the CR-10 to have a lug for the Articulating Camera Mount. The v2 parts fit a standard CR-10 bed, mirrored for the left and right bed corners. The v3 parts...

... designer to mount on the right-rear rail upright. The main CR-10 specific piece is the mainboard case, designed to mount to the left rear frame rail on the outside of the rail. This is my first design I'm posting, so please be gentle. ...

... doesn't have to be screwed in at all. It's just a locking mechanism, so the axle won't fall out. 3D printed parts list: 1 Pin 1 Mount 2* Side You can see more details of this part in my video about the CR-10 v3: https://youtu.be/cT5pjpX8q60?t=756

This is a removable build plate for the CR-10. It uses easily sourced items in the US. I've been using it for quite a while and I have had no issues with it. This setup consists of a 12" X 12" X 22ga. steel plate and .7" neodymium magnets Home Depot....

Crafted specifically for my trusty Creality Cr-10s, I'm confident it will fit seamlessly on the standard Cr-10 model as well. To get the best results, print with a resolution of 0.1 to 0.2 millimeters. Don't worry about the regulator; simply grasp...

... have to be screwed in at all. It's just a locking mechanism, so the axle won't fall out. 3D printed parts list: 1* Pin 1* Mount 2* Side You can see more details of this part in my video about the CR-10 v3: https://youtu.be/cT5pjpX8q60?t=756

I just upgraded my Creality CR-10 to a CR-10S 300 and had the chance to organize my cables again. I wasn't happy with the filament tube movement and hotend cable arrangement, so I designed holders for the end stop holder and hotend attachment. For...

Due to the friction caused by filament rubbing against the housing of the switch, I searched for some filament roller solutions and found OneBadMarine's Cr 10 S PRO filament roller guide (http://www.thingiverse.com/thing:3148615) which includes a...

This adapter enables you to securely fasten a Raspberry Pi Zero W to the control panel of your CR-10 printer. On my own CR-10S 40, I found that it's possible to supply the Pi Zero with power directly from the USB port on the printer. To accomplish...

... filament runout detection sensor. Just remove the existing M3x20 flat head screws and replace them with slightly longer M3 x 25mm socket head cap screws.Check out my review of the CR-10 Smart and keep an eye out for more upgrades coming soon! 

... your filament runout detection sensor. Just remove the existing M3x20 flat head screws and replace them with slightly longer M3 x 25mm socket head cap screws.Check out my review of the CR-10 Smart and keep an eye out for more upgrades coming soon!

The holes printed a little small on my CR-10 so I just drilled out the small ones for the filament and re-tapped the M6x1 threaded holes. My original arm design did not have the filament guide at the tip (you can see that in the top view picture....

This design interfaces only to my CR-10 v3 Filament Sensor Relocation Bracket: [https://www.thingiverse.com/thing:4716470](https://www.thingiverse.com/thing:4716470) This isn't a remix of __Biffo318__'s design, but its positioning and configuration...

The new standalone has been designed to accommodate three types of motherboards: CR-10, CR-10S, and Mks Gen 1.4. It is also possible to add other motherboards and adapt a support on the existing anchors. The Standalone Mod consists of two main...

1.3 with standard Lens only.\r\n\r\nTo install the Cameramount, place it on the backside of the right baseprofile of the CR-10.\r\n\r\nYou will need 5x M3 for the Cam-case and 2x M4 + 2x M5 screws for the mount-arm.\r\n\r\nIf you appreciate my work,...

My CR-10 Control Box does not sit level on my shelf and wobbles every time I hit the button, so I designed a shim to put under one of the feet. It should account for a ~0.75mm distance, and almost perfectly levels my printer control box. I printed it...

Hello,\r\nThis is the BreezeBlock fan shroud for the CR-10 Printer. I set out to design a streamlined fan shroud that seamlessly integrates with the 5015 blower, boasting a slim profile without sacrificing functionality. Additionally, it was crucial...

I took the original CR-10 control box stabilizer design and gave it a sleek makeover by adding some fillets to soften its sharp edges. I also thinned out the design since it doesn't need to be as bulky to get the job done. This modification will...

I crafted a bespoke adapter board, the back board, for the THC-01 hotend, a clever creation of tronic_, and it seamlessly integrates with my trusty Creality CR-10. I also designed a BL/3D touch probe adapter to match its sleek design. Furthermore, I...

... mounting the spool along the x-axis, giving you even more flexibility with your filament storage. It's designed as a companion piece to my CR-10 Direct Drive Conversion, which is available on Thingiverse at https://www.thingiverse.com/thing:2809256

The CR-10 V2 boasts several notable upgrades over its predecessor, but one area that still requires improvement is the wire harness. Currently, the wire harness attached to the gantry assembly is left hanging from a connector, which can cause the...

Two supports made to screw directly on top of the power module for my Creality CR-10. It is used for remote controlling the printer via octopi/octoprint. The relays control a 12V LED strip and the main power of the printer through the gpio ports of...

I created this aluminum profile connector to upgrade my Creality CR-10. I'll use it to build a compartment underneath the printer to hold all the electronic parts. I'm going to upload it once finished. This component can be used to connect every...

This is my take on a custom squash ball vibration dampener for the CR-10 S5. Nothing overly complicated, I've included the Solidworks file so anyone who wants to fiddle with the design can give it a go and make it their own. I went with ABS, but...