stormtrooper 3d print file

Print with layer height 0.16 and 20% fill.&nbsp;If you like my designs give me like and share. If you like them a lot invite me to a coffee.</strong><br><br><a...

Less than 2 minutes later, it was up to temperature, and held the temperature through several 2 hour prints without problem. I also tested with the fans at 100%, and 240 degrees, and it had no problems getting and staying at temp. The "box" part...

The pieces can be assembled in multiple different ways.  - Alien Desert bases: 19 different bases ranging from 30mm to 80mm, and including a desert rock scenery piece.  All the parts are pre-supported for SLA resin printing! Storyline of the...

Most parts need to be printed flat/horizontally before being glued together for maximum strength. The only exceptions are the Tops and Bottoms of major Leg and Thigh pieces where stepper motors should slide in. Gluing these together will prevent...

Mi sembra di avervi detto tutto.Buona stampa._____________ Kitchen Sink Carpet Hi, this is a simple but functional drainer for kitchen sink.Why did I do it?Being in quarantine for COVID 19 like everyone else, not being able to go out to buy it, I...

Print the required parts (some will need supports), glue the splash guard to the top of the airlift pump as pictured, cut the mesh to size and glue through it with the mesh retainer holding it in place on the holding basket's window (superglue was...

# Hardware - (2) 8mm M3 Screws (per brace) - (2) M3 Hex Nuts (per brace) Print at 80% infill and above for optimal strength. I would go so far as to use PETG/ABS instead of PLA as the latter is brittle and has a tendency to fissure under...

A modular board design helps with capturing the fine details of original design, as larger individual tiles can be separately printed even on smaller beds; additionally, the tiles can be easily stored. Game Rules Each player takes a set of seven...

Tube (material doesn't matter, i chose stainless to match the optics of the bowl) some kind of epoxy glue assembly: after printing the required parts and buying the hardware you can start by assembling the scissor mechanism with the countersunk bolts...

FR: voir plus basBlocking supports in CURAReset (and afterwards set again to avoid later inconveniences)Preferences > General > Ensure models are kept apartPreferences > General > Automatically drop models to the build plateSet support ON in your...

Manifolds pictured were printed using nylon 6,6 weed-whacker line because that's what I had on hand that could handle heat and chemical exposure. I believe ABS/ASA would actually be a superior option, as you could use acetone to seal and fix the...

Two are required, the shape is rotationally symmetrical so only one model is needed, and printed twice. The jig is 2RU (3-1/2") high which is the same as the smaller PDP-11/03 chassis height. To use, simply push the jig into the rack from the...

It is important that the tissue had a melkoformatny print, or fabric pattern may not match the image of the doll. Tilda is usually carried out in a compact size, so it is best that the fabric was not a major figure. Dolls Tilda sew two ways this...

They can be printed with PETG, ABS, or Nylon materials, but PLA is not recommended because it's not elastic and heat resistant enough. Type 1a: Car Mini Relay Socket This type of socket has five contacts that are 6.3mm in width and is designed for...

2.6mm thickness - I used something like these:...

**Gravitrax Ball wheel V1** - Difference in height 80mm - no support necessary - 3 pressure parts: wheel, gear, pillar - Printing time approx. 6 hours - you need: (motor see links) 5 x magnets Ø 5mm x 3mm 1 x M4 screw 45.0mm or longer or threaded...

Every glance at this work of art will make your eyes light up with admiration.Printed in PLA or PETG, the robust material ensures long-lasting stability, giving your board a firm hold while creating a harmonious connection between window and...

The V3.1 box has been on the printer for around 150 hours of printing with no evidence of overheating of the TMC drivers or the Raspberry Pi. I had to ramp up the ref voltage for the 4988 extruder driver from 0.72 to 0.85 to alleviate some skipping...

### How to Assemble the Clamp Charger: Print out all the parts and check if they fit together. The clamp holes might require some fine-tuning of the holes on the clamp (this depends on the material you selected for the clamp and cradle). After a...

Consists of:- A mount of direct drive BMG BondTech extruder kit and stepper motor NEMA 42x22 0.8A.- Mounting and covering BL Touch from Creality.- A duct of dual-blowing and 4015 front fans.- Cable management.&nbsp;How I Designed This&nbsp;Autodesk...

(I use 4 x 25mm M2 screws) For mountig my rx and vtx, i printed 1 x vtx_base.stl which fits onto the fc stack. For the rectangle standoffs you need 2 screws and 2 nuts to fix it. These standoffs are inteded to use at the left, right and rear side of...

I'm creating a modular table game that doesn't require dice - you simply print the pieces and cards. The game involves building a spaceship from its most basic beginning to an interspace station with many inhabitants and resources to manage. It's...

... with this new hose adapter. It is available at the link below: https://www.thingiverse.com/thing:5011414 Print Settings Printer: Snapmaker 2 Rafts: NoSupports: No Infill: 25% to 30% should be fine Filament: n/a PLA Black Category: Machine Tools

... support manned missions indefinitely. This project was created by myself and Dan Pettit (fellow IGG developer). Due to printer maintenance, I haven't been able to complete the printed parts, but it's nearly finished, and I'll post pics very soon.

Only disadvantage: Ender3 only has 200x200 to 220 to 200 mm print area. The arm is too long for this Maybe a friend has a bigger printer Here is my "all-round package" with 120, 135 and 140 degree holders for the common 2kg rolls. The original...

The plate was designed to be printed flat without any supports, which makes it a little different from most printable plates available. However, you will lose some travel on Z height due to the motor being on top - roughly 45mm. You'll also lose...

When I built my dedicated printing room, I failed to notice that the switch for the overhead lights was located at the top of the rear wall, which is not very convenient. This design has 4 main parts: The Switch Plate mechanism, The Corner "Pulley",...

For VTX antenna, I use TrueRC Singularity short ufl LHCP antenna https://www.racedayquads.com/products/truerc-singularity-5-8ghz-short-u-fl-antenna-rhcp-or-lhcp?variant=31387077476465 Print using 0.2mm layer height. 100% infill with support. For...

MegaMAME is a large console which can be stood on a table, or you can use the stand to hook it over your knees while sitting on the couch :-) I had to split the case into two parts to be able to print it on my Ender 6. I'm happy about how it turned...

This is a Starter and his Command Box extension for the 22RE Toyota Engine (https://www.thingiverse.com/thing:644933)The video of the finished project : https://www.youtube.com/watch?v=Oly5FVFVWa0 Print instructionsPrinter: Geeetech A10Rafts:...