sunshot 3d model

I have the Armattan Chameleon Ti, and plan to create these stuff for it too. If you like my designs and use them regularly, consider a small donation :) I promise I will update these models to become better and better. Print Settings Printer Brand:...

It's just a model I whipped up, and sliced it with a bunch of retraction changes. Then went back and spliced all the g-codes together. Base Cura profiles I use: layer height - 0.2mm Optimize wall print order (do not retract before outer wall), print...

The diameter is 50mm, 23 teeth, pitch 2, height 20, slop .01.Updated threads were created using Fusion 360 and then incorporated into the Tinkercad models.  Several versions were tested at various tolerances to get just the right fit across...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

[Medium Sized Model - 25mm Base] [Presupported with LYS files in 32mm & 75mm Scale]   Once a member of the elusive Psithars, Bastian abandoned their order over their methodology and views on non-humans. He moved to the University of Canos, wishing to...

This would not work on a single nozzle printer, so we opted for truncated tetrahedra with slight insets on two of their triangular faces. INSTRUCTIONS Everything prints at 0.2 mm layer height.Set your line width to 0.45 mm, as the pattern...

DO NOT LOOK AT THE SUN WITH THIS!Also have a look at my improved Dobsonian Design:https://www.printables.com/model/317112-propdob-telescope-foldable-travel-dobsonian-45-mir Hi, this is a Newtonian telescope with a 114 mm diameter mirror and...

This model fits seat shafts with a 16-groove, skip-tooth-top, 12mm nominal shaft: (note skipped groove, blue arrow) Probably best to print these with the spud pointed up for minimizing how much trouble the overhangs inside the hole will...

phone_model_customized = Yes, it is now set at 0 custom_left_port_y_position_disabled = No, has been set by the default of 0 as requested above bottom_port_corner_radius_customization_enabled = Yes, now has a custom setting equal to 5...

Make sure you select your arduino model and com port. Extract the files There is a marlin.ino in there that you should select Then upload to your Ramps board and it should work, I'll test the sd card and lcd when I get the bits. I would definitely...

Make sure you select your arduino model and com port. Extract the files There is a marlin.ino in there that you should select Then upload to your Ramps board and it should work, I'll test the sd card and lcd when I get the bits. I would...

It's now less expensive to build (when building 3+), more water resistant, and offers more space for alternate battery options.https://www.printables.com/model/297089-meshtastic-solar-base-station-node-enclosure-for-3---Build a complete Meshtastic...

This is a well known test model with many remixes.However, I have not seen anyone with automatic temp range.Existing temp tower is “semi-automatic”, they set temperature to preset levels with custom g-code in “before layer change”This print set...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Orient the model on the flat surface in PrusaSlicer then paint supports on the lower edges of the camera shroud. Set supports for enforcers only.AssemblyThe Raspberry Pi 4 (I used a 4GB) and camera V2 are held in place with a couple of screws each. ...

My daughter loves playing chess, but the magnificent pieces by NTX9 often fall out the original box when she tries to relocate.Therefor I made a remix that allows for a lid to slide in front of the pieces. The lid is of course based on the pieces...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

Printer Settings: * Printer Brand: RepRap * Printer Model: Original Prusa i3 * Rafts: No * Supports: No * Resolution: 0.2mm * Infill Percentage: 25% Print Notes: I utilized a 0.8mm nozzle to expedite the printing process, which took approximately...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 27...

also know with ESC if you turn power off with pot turned to high you have to turn the pot down to be able to start motor again (must be a ESC safety thing) Machine drilling a board the failed to drill completely through on the CNC PCB Mill ( My fault...

All necessary supports are pre-applied to the models (there is no need to add additional supports). The main body of the stein/mug prints with cylindrical supports, the left/right lid have perforated supports, the lid top doesn't require supports...

The model can accommodate slightly larger and smaller sizes as is. To fit your doorknob you may either scale the STL file before printing (measure your doorknob diameter D and scale by D/54), or adjust the parameters in OpenSCAD, render (F6), save...

The current model is sized for a 28mm long motor, if you get a longer or shorter one a new set of files will have to be generated. If you do not have access to Inventor let me know and I can generate the files for your size...

But the base design is a mix of: Ichibey's Sakura CoreCube Hbot modeling work Jetguy's lasercutter templates and electrical / extruder configuration DNewman's Sailfish programming for CoreXY gantries Credit should go to the above -- I'm just...

On my version, I suggest that you start with 4 seeds in each of the 12 pits (print 4 copies of the 12 seed model and then separate them using nail clippers or small scissors). Increase the number of seeds in each pit progressively to increase the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

I've uploaded the STEP files, so feel free to remix the system to fit your printer model! Just give me a shout-out because it took a lot of hours, dozens of printed iterations, and plenty of PLA. The IR Probe is mounted to the connector by design...

The battery negative is connected straight to the Anderson PowerPole negative and the radio negative.The model includes a plate to put on top of the batteries to ensure nothing gets in and shorts them out.To make the antenna fit inside the box with...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...