switch stands 3d models

2 torso’s upper options 2 x right leg options 1 x optional cubs to stand/hook to side of bath 2 part bath tub 1 x Happy Head 1 x left leg 1 x Water Lid 1 x lower non-detailed torso 1 x memory card tray Torso pin is included, rest of parts are keyed....

#KIDS JEWELLERY Earrings For Kids Add A Touch Of Whimsy And Playfulness To Their Attire, Ensuring They Stand Out In A Crowd. Pendants Serve As Adorable Personal Accessories For Little Ones, Often Featuring Endearing Animal Designs Or Symbols. Nose...

At the bottom of this summary, you’ll find a list of all the members of the collection. Boo!4 tilts when standing. Two size models are included.</p> <p>Boo! 4 prints great in one color. White is always right, but pearlescents or silky whites work...

I've also updated the printing files so they match each other better, such as improved stand-offs and better alignment of connector holes for even easier assembly. All that's left is printing out four or five parts - the lower and upper sections,...

To print in bulk, rotate them 90' X (so they stand up) and then 45' Y (so the numbers are not directly facing the plate). Support the bottom side heavily. Add a lot of heavy supports on the bottom edge closest to the plate. This may require more...

Athena stands poised at the center of the pediment, as a fierce battle rages on either side of her. The warriors are armed but nude, except for the archers, one dressed in Oriental fashion and the other wearing a traditional short chiton under...

This design requires no supports at all, so you can print the tower on its side and the stand flat. Simply apply some strong glue or super glue after doing a test fit with it, and you're done. The spacing between the cuts is approximately 12mm. I...

-STANDALONE SYSTEM- This system will stand in the bucket in a secure manner with no requirement for rope attachment to the top. 1. Hydro tower bucket fitting and pipe stabilizer The bucket fitting applies to the bucket lid as shown in the...

Hardware Required: 6 x M4 30mm Hex Stand-Offs 4 x M4 20mm Hex Stand-Offs 12 x M4 40mm Button Head Hex Screws 14 x M4 12mm Button Head Hex Screws 6 x M4 Square nuts 1 x M8 75mm Bolt 2 x M8 Washers 1 x M8 Hex Half nut (Optional, used with thinner...

The end result is EXTREMELY sturdy, and can support my body weight if I stand on the corners. <b>Some Notes:</b> I would recommend using the same brand filament and color, if you have the choice. Different filaments can have different...

You can choose between a small and a big stand - the small one should be attached to the surface with some double-sided tape (or else), while the big one doesn't need attachment. Print the bird parts in different colors, but make sure they're all...

- I am curious to see your uses in the wild!If you like these random buttons, have also a look at my other random creations like the reindeers, pack of dogs, rabbits and santas.Also check out my configurable text based creations: multi-line label,...

I have included a small case for the control module as well, but it is not integrated with the spool stand as the unit is meant to fit inside my filament dryer. The plastic base is quite smooth so you will need to apply something to the base to...

The links are just suggestions, there can be other compatible options: 4 x 380/385 brushed motors 380SA-3065-55...

You can potentially combine the feet, poles, joiner and stand, however, the other parts will likely need to be printed on their own. The poles have been pre-cut in half to reduce print time and allow printing on printers with less Z height. The...

With everything printed and assembled the weather-pagoda weighs 116 gr.Top and bottom had a bit of stringing where parts stand out, the rest came out really clean. Setting the floors on the columns will need a calm hand, it's tight. Be aware that...

The base design is a remix from the GE Spiral Tree Stand https://www.thingiverse.com/thing:4680632. Had bought four of these for my show and decided to build two small trees to go beside my Mega tree. The topper was designed after several...

One key point is that the pins have to be printed standing up, which reduces their structural strength quite a lot. Printing the pins horizontally makes them much stronger (I tested it), but that means having to fill the bed one pin at a time, which...

 I am not sure if super glue will work with PETG very well, and it does have a tendency to leave a white residue when it cures.The mounting stakes are NOT glued in, so they can be removed and replaced with the optional stand, if desired.This will...

I plug the sensors directly into it so it gives both electrical and mechanical connection. With everything printed and assembled the weather-pagoda weighs 116 gr.Top and bottom had a bit of stringing where parts stand out, the rest came out really...

The wheel is quite large, standing 1 meter tall and almost as wide. For those who frequently adjust bed leveling, be aware that I leveled the bed before starting the project and never adjusted it again after printing hundreds of parts. Tuning was...

Largely basing the placement of hooks and weights in the system off of the aforementioned awesome video, the real task in designing this object was creating the stand to hold it up and the snap-in hooks for easy printability without supports. I...

If you happen to visit Aachen one time, contact me and I will buy you a coffee or beer. Print Settings Printer: custom Rafts: No Supports: No Resolution: 0.15 Infill: 15% Filament: 3DJake ASA green Notes: I used ASA from 3D Jake but you can choose...

Dilapidated attractions and vendors’ carts stand frozen in time alongside the rusted skeletons of forgotten rides. Once a hub of fun and laughter, now it’s a crumbling and labyrinthine deathtrap filled with peril.  The world may have ended, but the...

The 140° beam is great for situations that call for working in close proximity to lights such as in a paint booth.Wiring: The EPL-TFM-150LED-RT-140DB-100-1523 is equipped with 100 feet of SOOW cord terminated in an explosion proof 1523 straight blade...

This miniature stands approximately 5.9 inches tall and I recommend printing it at full scale to preserve its intricate details. Instructions I created this project because I believe London's red phone booths are a beloved landmark that everyone...

I build this qi charger so I could charge while viewing on my night stand but also found I could print the body/back pieces, glue them together with super glue and mount it on a vertical surface using double sided tape.  I also wanted something I...

This allows me to access the CF tube fitting, if having trouble getting into place, without un/screwing anything **Optional: Use CA glue on the inside edge of wing3 to make the edge stronger and stand up better. Put a good bead of CA glue along the...

Становлення assistant The design process, led by Alias Design, resulted in a visually stunning and unique creation that stands out from the rest. Становлення<|im_start|> assistant This captivating creation was brought to life through the innovative...

The arm was spray painted with 2 layers of chrome spray paint. The LEDs were installed in the base and fixed with some hot glue and zip tie. The stand_*.stl parts where glued together afterwards. Finaly the arm received a washing with black shoe...