t cup 3d models
479832 3d models found related to t cup.thingiverse
English To this day i have not printed it yet. Feel free to give it a try. Français Jamais imprimé à ce jour. Donnez moi des nouvelles si vous l’imprimez. ... 25 février 2018
thingiverse
Cup holder for Smok T-Priv. Also will hold a 15ml juice bottle as well as a pen or two (or something the size of a pen). Thanks for checking it out... This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/jiEOF8PU8En
cults3d
ninja turtles themed can cup. ...use a piece of 1.75 filament as the hinge pin.
thingiverse
No preload shock cup for losi mini t springs used on traxxas big bore shocks or others with 6mm shock link end.
thingiverse
Edit it online https://www.tinkercad.com/things/61JDUMPheJF A simple spring cup, solid design-no shaft cutout for more strength, for using losi mini-t springs. It is for a 6mm OD rod end and a bit less pre-load. ...Design fully open if adjustments...
thingiverse
... Tinkercad. ...Edit it online https://www.tinkercad.com/things/dFJg7x681gC Spring cup to allow use of Losi Mini-T springs for a crawler. This model is for a 7mm OD rod end (e.g. TRX-4). No cut out for more strength. ...Design offers a bit less preload.
cults3d
Mini-t Spring Cups for SCX10II Shock Absorbers
cults3d
I lost a spring cup on my T-Maxx. I designed up one it cost me $.06 to make. ... a lot better then buying a set.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=129360 Instructions Using the following options: brp = 80 wall = 0.6 tr = 13 details = 120 textrota = 0 ctext = DON`T TOUCH MY CUP. ...mrp = 12 h5 = 1 h4 = 2 h3 = 17 h2 = 6 h1 = 5 h0 = 0.5 po = 4...
thingiverse
... mill 2mm deep like on the standart Vacuumcups. I have included a 3D drawing of the base plate where you can see how the base plate should look like. The T-Nuts accept 5mm nuts so you can mount what ever you want, like a low profile clamp. ...
thingiverse
Two T-Slot fluid cups are shown one in Yellow and one in Red. I had a metal can and it kept sliding around or off the mill so this is what I now use. Made the rectangular bottom part separate and super glued it to the flat bottom to avoid printing...
thingiverse
cup for trx4 stock shock to be used with mini-t spring. ... Made one for the upper part as the spring goes sideways under compression.
thingiverse
... bored to find my personal cup taken away by cleaning personel. ..."If somebody has to break it, it will be me..." So I created this "Don't Touch" sign to put on top of my cup. ... Inner diameter 82mm, obviously: scale the stl to get other measurements.
prusaprinters
replacement rails for chrysler town and coiuntry rear cup holder 2001 - 2007 modelsprint at standard quality .20 at 20%fill or higher as needed.
thingiverse
I lost a Spring cup for my Traxxas T-Maxx. I designed up this one. It is a snug fit but can easily be changed out. This cost me about $.06 to print one. ...
myminifactory
Fairly simple losi Mini T 2.0 shock cup replacement. ...After seeing you could only buy full shock sets it seemed easyer to simple design a replacement that was cheaper.
thingiverse
In a Volkswagen T-ROC without wireless charging option you need to connect your phone manually to an USB-cable. An iPhone 7 slides in this cupholder and connects to the USB charging cable fitted inside. It fits in front of the gear lever. Now...
prusaprinters
In a Volkswagen T-ROC without wireless charging option you need to connect your phone manually to an USB-cable.An iPhone 7 slides in this cupholder and connects to the USB charging cable fitted inside. ...It fits in front of the gear lever.</p><p>Now my...
thingiverse
Customized version of https://www.thingiverse.com/thing:3852842 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3852842
thingiverse
Made these as a fun thing during the FIFA World Cup 2018. Optimized for 0.6mm nozzle. Printed in PETG due to great material properties and layer adhesion. Used dual settings with 0.3236 layer for the bottom part and 0.1618 for the cutting...
thingiverse
This year I upload a new cup every week... Instructions Download, slice and print. This one was sliced with Cura [Super super fast] at a pretty low resolution 0,25mm layer height. ...print time: 22...
thingiverse
Are you tired of guests leaving cups of things all over your house-- cups of water, cups of juice, cups of goldfish, and cups of unidentifiable red liquid? (We all know that guy.). Wish you had some way of forcing your guests to use coasters, or keep...
thingiverse
This is a Knock off of something I found a picture of on internet (sorry can't find it again to give credit) but liked the idea so here goes. Simple Foam Cup Holder with finger loop for Hot beverages or just a better grip. hope you enjoy. ... **Just...