tacblades 3d models

... If used with the feet then place on a anti slip surface or mat. All Tacblades designs are tested and printed before posting. ...All designs and created with 3d printing from the beginning so minimal support and angles designed to print easily.

Remix of Tacblades folding stanley blade with improved top cover. Internals as per original version. ... Print this top & Bottom cover along with the original bolt & Internals to create a complete tool.

A simple small test print Prints at 0.1 layer height in 30 mins. It was designed to test the majority of aspects you see in general prints. Great for testing new filament. ... Tests: Stringing Ozzing Bridging Ringing Ghosting Zits and Blobs ...

Verbindung der Teile mit M3 Schrauben und versenkten Muttern

... material can make that fine design not work as well. I have updated this design three times, because I still like the feel of this design by TacBlades. I think now there are enough interlocking parts to make it safer and sturdier for my use. ...

Disclaimer:Tacblades will not be liable for any damage or injury as a result from use or misuse of the knife printed from these files. ...It is the responsibility of the owner to handle the knife with care and its intended use as a tool.It is the...

This is a case for the Sony AS-20 Action Cam Its been designed to have access to all the ports and I/O even when tripod mounted. It requires support to print upright, so I have added a sacrifical plug in the thread that is removed after printing...

Tacblade Utility Stanley Blade Folding Knife Remix Verfeinerter Version der super Vorlage.

... of the parts, please refer to the original version of Tacblades. https://www.thingiverse.com/Tacblades Tacblade Utility Stanley Blade Folding Knife https://www.thingiverse.com/thing:2521858 Translated with www.DeepL.com/Translator (free version)

Disclaimer: Tacblades will not be liable for any damage or injury as a result from use or misuse of the knife printed from these files. It is the responsibility of the owner to handle the knife with care and its intended use as a tool. ... It is the...

Tacblade Utility Stanley Blade Folding Knife (https://www.thingiverse.com/thing:2521858) by Tacblades is licensed under the Creative Commons - Attribution - Non-Commercial - Share Alike license. http://creativecommons.org/licenses/by-nc-sa/3.0/...

This is a remix of TacBlades fast live leveling resized for the Ender3

just a remix of tacblades great work... ...credit goes to him my 5015 fan was vibrating like crazy and this is much better...

This is a remix of High Clearance CR-10 OEM Fang Mod created by Tacblades. I rotated the 4010 fan 90*. Print settings remain the same as the original. ...I used Tinkercad to remix this thing.

A remix of Tacblades CR-10 Leveling Assistant (https://www.thingiverse.com/thing:2556462). This was made for 200x200 printers that don't have an option to move to each corner. The gcode will move to each corner for 10 seconds, play a tone, and then...

... ... Universal fit for phones thickness from 5mm to 11mm Easy to print. All Tacblades designs are tested and printed before posting. ...All designs and created with 3d printing from the beginning so minimal support and angles designed to print easily.

this is a combination of the fan size adapters by (TheMeerkat) and the fang mount by (Tacblades). I recently upgraded my U20 to a volcano hotend and could not find an adequate fan mount. These are for 50mm fans. ...I may design a nozzle for the hot end...

For modelling the structure of the whistle, the following work by Tacblades was also used as a reference: https://www.thingiverse.com/thing:2662731 I have only printed at 100% magnification, but I think the sound will vary slightly with enlarged or...

And with the extruder mod described in the instructions, you can easily print flexible materials And following gunnar94's recommendations, I used Tacblades OEM_Fang_CR-10_Short3 for the fan mount without any updating. I love that it used the factory...

This is a collaboration between the zBrush Artist Mateusz Baran @mruglyhouse and 3D Printer @Tacblades The revenue is shared. The high poly count mesh was expertly crafted in zBrush then taken and reduced, healed and optimised for 3D Printing. The...

** Added GCode for leveling with a dial that fits in the bracket (Modified level file from tacblades for ENDER 3 ONLY). First level is at front left to allow you to set proper height however you like... Then it lifts up and sets the Dial on the spot...

Really like Tacblades high clearance fang for the CR10 but wanted something that could be installed and removed easier without unmounting the hot end. This version mounts to lower hole of stock fan shroud instead of heat sink screws. Allows access to...

This is a mashup of: This Fang-compatible BLTouch mount: https://www.thingiverse.com/thing:2994381 This CR-10 Direct-drive mod: https://www.thingiverse.com/thing:2869640 The whole arrangement is compatible with this Tacblades high-clearance fang...

use Tacblades easy leveling: https://www.youtube.com/watch?v=gkZUAyTxU1Q Find Tacblades here on thingiverse for other good mods too. Edit: 10.01.18 Just uploaded a new version. The previous one had a weird problem (what a surprise...) that was...

... files. I have added by PLA fff file if it helps (set for the CR-10) All Tacblades designs are tested and printed before posting. ...All designs and created with 3d printing from the beginning so minimal support and angles designed to print easily.

... this without supports but it does come out a lot nicer with them. All Tacblades designs are tested and printed before posting. All designs and created with 3d printing from the beginning so minimal support and angles designed to print easily. ...

The Tacblades Temperature Tower Can be used for any temperature range you like in Simplify3d or Cura Very fast and easy to print, has slotted section to test adhesion for the temperature above it. The reason it does not have temperature values on...

I really love the high clearance fang mod made by Tacblades. I really didn't like the high pitched whine that my OEM blower fan made though and that's what lead me to remix this. This is exactly the same as the original, only this accepts a...

Thanks to Tacblades for the original I've made the overall dimensions slightly smaller (198cm x 198cm) because Cura was saying it doesn't fit on my bed (maybe I should look into that lol) I also added a few more squares, to allow me to make more...

I made this to confirm level adjustments using a live-leveling technique similar to TacBlades Easy Live-Leveling where I print .2mm thick 20mm squares over the build plates 4 mounting screws in the corners and the center of the build plate. ...