tamiya rc 3d models
32852 3d models found related to tamiya rc.thingiverse
This is a Front Suspension Mount for a Tamiya RC DT-03 Racing Fighter. However, it may fit on other RC models. I designed this after my mount snapped following a heavy collision. I printed this twice ,1st with an infill of 40%, and 2nd with an infill...
thingiverse
Fueltank für Tamiya MAN 6x4 RC Truck 1/14 Passt auf den orginal Akkuhalter.
thingiverse
Tamiya 51270 RX7 inserts so you can flush mount your headlight covers. Shoe goo them in and use double sided tape Sakura D5 IFS delete shock tower added 1/10/2021 Sakura D5 angled ESC mount. Pint .2mm resolution (!). ...Use 2 x M3 X 12MM, 1 M3 X...
thingiverse
Battery Pack holder for Tamiya RC Car Chassis (TL-01)
thingiverse
2 axle fenders for Tamiya RC truck - LOW and "+5mm version". ...With mounting holes for this lights: https://www.thingiverse.com/thing:5037927
cults3d
2 axle fenders for Tamiya RC truck - LOW and "+5mm version". ...With mounting holes for this lights: https://www.thingiverse.com/thing:5037927
thingiverse
This is a body shell mounting post extender for RC vehicles with a 6mm mounting post. Copyright DP. Free for personal use. ...May not be sold or used for profit.
cults3d
Double servo support for 1/14 Tamiya RC truck tractor
thingiverse
Hier die Achse für Doppelbereifung beim Tamiya Auflieger. ...Rahmenbreite 30mm Kugellager 8x4x3 und 6x3x2 werden benötigt. Die Schraube ist für die Tamiya Kühlaufliegerlenkachse und gibt es bei Modellbau-Seidel einzeln. ... Viel Spaß
thingiverse
( TAMIYA #58645 Subaru WRX STI 24hr Nurburgring ) - Front ( first draft ) - Rear ( first draft ) - Fog ( first draft ) Draft Versions, Yet to be fully tested ... ( They require re-working to fit better ) Welcome suggestions for other mods to this...
thingiverse
Simple shells to protect standard size NiMH packs and take up excess space when used in the Tamiya Frog and Hotshot. Got tired of seeing new batteries in my son's cars take such a beating! Battery slips or snaps into the shell, and the shell is...
thingiverse
Das ist bei Höherlegung des Tamiya High Lift Getriebes für mehr Bodenfreihei und den umbau der Firma BaMaTech eine neue Rc Platte, da der Motor dann auf der Seite sitzt. This thing was made with Tinkercad. ...Edit it online...
thingiverse
The off-the-shelf round LiPo's don't fit into the older Tamiya models as they are approximately 5mm too long and this design allows for upgrade while still working with older chassis dimensions. LiPo battery significantly improves the performance of...
thingiverse
Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...
thingiverse
After a impact with a wall, the plastic steering arm that connects the wheels to the servo broke. this is a replacement part that only has the holes required to suit the lunchbox frame. Also the original part is counterbored and a plastic washer...
thingiverse
just a 3d printable servo mount designed to be pre-drilled with a 2.5mm drill
thingiverse
Replacement Driver Arm for vintage Tamiya RCs
thingiverse
You will need some new longer m3 18mm screws (I used some spare tamiya screws I had leftover from some builds) and nylock nuts. There are recesses in the part that accept the nylocks and allow a tidy install. ... New ride height at the front of the...
thingiverse
3D printable replacement body clip sockets (the things the body clips clip into).
thingiverse
But i think it fit on more tamiya/other RC Car. I print from PET-G filament, for more flexibility. Racommende ABS or flexibile filament. Comment if is good PLA, i did not try yet. Dimension: 197x45mm Height: 21mm Hole distance: 30mm (fit...
thingiverse
I've Modified my Tamiya MAN TGX Truck, for that I used a 2nd frame. To support the frame and keep it straight I have copied the design from the original supports. they are slightly smaller so if you want to use them for the original Frame you have to...
thingiverse
This is an important part to complete your RC conversion (using Alessandro Giogetti's 3D Prints) of your childhood Tamiya Mini 4WD car. Check out full tutorial video below if you are planning to convert your Tamiya track car to RC. ... ...