temperature probe holder 3d models
357591 3d models found related to temperature probe holder.cults3d
This holds a temperature probe used for a digital cooking thermometer. ... A great replacement for the Weber temperature probe holder.
prusaprinters
DS18b20 temperature probe holder for probe measuring 6mm OD x 50mm length.Use double sided tape for mounting.
cults3d
TEMPERATURE PROBE HOLDER FOR ARDUINO, WITH CAVITY TO INDUCE IT AND THERE TO SEAL IT TO AVOID LIQUID LOSSES. HAS INLET AND OUTLET WITH 1/4" THREAD TO FIT ANY FITTING OF THAT SIZE. ...BE CAREFUL WHEN PRINTING AS IT MUST BE IN HIGH RESOLUTION TO AVOID...
thingiverse
This holds a 0.160" diameter temperature probe (standard thermistor size). ... A #6 hex nut drops into the pocket and a #6 screw is threaded into the nut.
thingiverse
This is designed to hold a specific temperature probe used in the Challenger Center Earth Odyssey mission. The temp probe was originally mounted to the arm with velcro. Print Settings Printer Brand: MakerBot ...
thingiverse
If you have multiple probes then these holders have been designed to be stackable, for easier storage. * **Layer Height:** 0.2mm recommended * **Supports:** Not required * **Brim:** Not required, but might be a good idea when printing the lights...
prusaprinters
This is the temp probe holder for a ThermPro model no. TP-19H, should fit any of the other color variants as well. It's a very challenging print on fdm due to multiple heights and grooves. The part has a integrated support for the lower. Turn...
thingiverse
This is a holder for an Atlas Scientific pH Probe ( or other appropriately sized probes) and a Waterproof DS18B20 Temperature sensor, which suctions to the side of an aquarium. Having these two sensors together allows for temperature compensated pH...
thingiverse
Thought my BBQ remote temperature probe sender needed a better mount so I made a dock for it. ...I'm using a strong magnet to attach it to the side of the pellet hopper but double stick tape would work too.
thingiverse
magnetic holder for ds18b20 probe. one side is wider than the other to take care of the plastic protection. ...magnet is 8x3mm
prusaprinters
The second is for the Enclosure Control system or #007 Temperature Control in the Mod's list. This is the same part just without a bolt and nut hole. It's meant to have a piece of 2 sided tape to hold it to the side of the right Z motor. ...The wire...
thingiverse
The RT-700 Wood Pellet Grill comes with two temperature probes which is great but there is no place to store them when they are not in use. The cable makes it messy, I then decided to create a storage place for these probes. There are 3 parts to...
thingiverse
... 40 / 3mm hole. ... https://www.omega.com/en-us/temperature-measurement/temperature-and-humidity-data-loggers/p/RH-USB-Series Fun fact, the serial number reflected in the USB descriptor of these probes will match the probe's serial number. ...Go Omega.
thingiverse
Support for Xiaomi Mijia LYWSD03MMC temperature probe to be screwed to the wall using a plasterboard screw. ... Support pour sonde de température Xiaomi Mijia LYWSD03MMC à visser au mur à l'aide d'une vise à placo.
cults3d
This is a temperature sensor holder for a digital thermostat. I made this for my RV to hold/hide the sensor for a 12v heater I designed. ...The dome cap will just glue on to the base.
prusaprinters
I believe the temperature probes are identical for iGrill Mini, iGrill 2, iGrill 3, and Weber Connect sensors.I suggest printing it with ABS or ASA. As uploaded, the holder is sized to be printed with ABS. When I printed it with PLA, it was a tad...
prusaprinters
This is a magnetic holder for temperature sensors. You'll need a 8x4 or 8x3 mm magnet. There are three versions of the holder. ...The smallest one should work with sensors of ~4 mm in diameter, the middle one fits sensors of around 4.9 - 5 mm...
prusaprinters
A simple quick print to mount a ds18b20 One-Wire temperature sensor outside. parts glue together. ...i printed it in ABS to not deform in the summer sun.</p>
thingiverse
Temperature probe holder for the Weber iGrill mini: www.weber.com/US/en/accessories/cooking/igrill-and-thermometers/7202.html
thingiverse
Case for the Riden RD6018 power supply with the following features - cooling fan duct - versatile temperature probe holder - 6mm shrouded banana sockets for input power - a friendly reminder about the supported input voltages and polarity When not in...
thingiverse
This is a temperature probe holder I made to sit on top of my pellet hopper for my Traeger Pro 22. The hopper lid will sit right on top of it (theres a slit for the lid to stay in place). Theres also a small rack to store your cooking utensils. ... ...
thingiverse
... vlastní sondy. Stackable temperature probe holder for grilling and cooking. Version 4.1 solves the problem of supports in the area of the probe holder This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/3JnoTDeQzNb
thingiverse
This ring will make it easy to place the temperature probes into the vent hoses and hold them in place a little more sturdily
cults3d
Temperature probe support. It can also be used for the cables of the brewing pumps. ... This support is for a glass of thickness 12mm
prusaprinters
This temperature probe organizer is designed for the Rubicson wireless BBQ thermometer with 4 mm probes that can be found at kjell.com in Sweden.There is also a step-file attached for easy modification.The parts are intended to be glued together.I...
prusaprinters
This mount holds a temperature sensor module with an outside dimension of 26x45mm.Such as this unit.It is intended to be glued to a surface, or just sit.Print with the outside face on the build plate.
grabcad
High temperature pressure sensor probe, length 6". ...With coolent water inlet.