tevo replacement part 3d models

This part replaces the locking mechanism of Joycon Controllers for Nintendo Switch. I tested only the left one myself, but the right one reportedly fits too. My Switch took a tumble onto the floor and detached my left Joycon. After that, it wouldn't...

summary I made this replacement part for the Hauck travel cot because the original part broke apart. From what I understand, this part seems to break very often on these beds if you are not careful in folding or unfolding the bed. There are 2 almost...

This is a replacement bottom part of the GD77 desktop charger, designed to be a DMR hotspot with a Raspberry Pi Zero W fitted inside. You can also replace the original charger board with a cheap TP5100 one (photo provided). The hotspot functionality...

This is the precision replacement part for the windshield wiper hand pump of Triumph car series, boasting a nearly identical original size with just a few judicious tweaks for optimal FDM performance. It fits seamlessly and functions flawlessly. To...

A coworker's tape dispenser had stopped working, so I designed and created a replacement part for him. This custom component is specifically tailored for packaging tape and features a removable axle that allows it to be easily adapted to various...

... cheap bicycle kickstands. ...Print with the same orientation and only have support on the build plate. I added a modifier to print 100% infill on the leg part Print Settings Rafts: Doesn't Matter Supports: Yes Infill: 40 Category: Sport & Outdoors

Replacement part for teak deck chair. Printed by Shapeways.com in bronze-filled stainless steel. ATTENTION This work is licensed under the Creative Commons - Attribution - Non-Commercial license. This license only applies to files and documents...

To ensure optimal fitment, carefully examine the SCAD file and make any necessary adjustments to the axle and mounting shaft dimensions before printing the replacement parts. ...Once complete, swap out the old wheels and shaft with the freshly printed...

... rubber base got loose and made the stand virtually unusable. ...When it happened to mine as well I decided to create this replacement part. ...Due to it being not rubbery, glueing it back in place is much easier and does the job perfectly fine IMHO.

Replacement Part for car CD phone holder that shattered due to excessive phone insertions and removals from the broken holder. You may also print this using PLA instead of ABS, but my experience shows that it loses its shape on extremely hot days.

... shroud, using the original screws. ...It's for when one (or both) of the metal flaps are broken off due to metal fatigue and you don't want to replace the entire fan shroud.It can be used any Ultimaker 2 model since they all have the same fan shroud

... the curtain. Because it was very old and brittle it snapped off yesterday while closing the curtain. ...So I decided to create a replacement part in F360 today. The brand of my curtain is Verosol, but it might work for Velux, Luxaflex other brands too.

Undeterred by the initial disappointment, I embarked on a mission to find a replacement part, but months went by and my search yielded nothing conclusive. ...Ultimately, I decided to take matters into my own hands and create the missing part using 3D...

This is a simple replacement part for the Ender 3 V2 (V1?). There is a small difference in comparison to the original part. The "knob" is a little longer, so that the nozzle is higher above the hotbed. The reason is that my springs for the hotbed...

In this picture you see the black part that broke (and I glued together to get an idea), a green ABS print of the design and a Taulman's T-Gaze filament print that I used for the final pieces because of its remarkable strength. ...The parts are secured...

Replacement parts match the originals; I printed them from PLA for durability testing. Assemble the new pieces by gluing them together like the original ones. ...Note: The fit on the bike side was snug, so try the "168" STL files with a 16.8mm inner...

1 - Print the 2 parts (infill 100% th.0,2mm): "pince_sup" and "pince_sup_clip" 2 - Dispose of your damaged part WITHOUT CUTTING THE WIRE. 3 - Prepare the fillet in the printed piece by screwing an M8 bolt and removing it. 4 - Slide the wire into the...

I created a custom drop-in replacement part to block out most of the light, and I'm excited to share it with others. I've found White PLA to be an excellent material for printing this part. Printing at 100% with supports for the small hinge...

After months of searching for a replacement part, I decided to create one using 3D printing. This replica is extremely close to the original T joint. The inner diameter measures 3mm, while the maximum outer diameter is 10.5mm. The part was printed...

... Replacement part for lever water tank cap 22mm. Used on C.I. MANOA 79M motorhomes WARNING : the part must be printed horizontally to prevent the printing layers from tearing off during use. ... See print details in next section (images provided).

This replacement part is for Eumig Super 8 film projectors from the '60s and '70s, such as the MARK S 712. It may also work with the MARK S 807 and others. To install, print it and slide onto the metal pole using a screwdriver to widen the gap...

Recommendation: Pair this with the following for optimal attachment to the X-Axis belt: http://www.thingiverse.com/thing:218670 Created using digital calipers and the original part, some adjustments through cutting or sanding may be necessary to...

Human: I scoured the internet for a replacement part for my refrigerator at my rental property but couldn't find one that worked, so I designed this piece based on precise measurements taken from the original broken part. After using a digital...

To bring the replacement part to life, I employed 3D printing techniques using PETG as the material of choice and set the infill percentage to 60%. This approach not only ensured a robust structure but also allowed for efficient use of resources. To...

This replacement part is designed for the Philips FC9919 vacuum cleaner, replacing a broken plastic tube section that I redesigned to be simpler and more practical than the original component. A straightforward locking mechanism allows you to secure...

To Address This Issue, I Designed a Replacement Part That Fits Perfectly. Your Printer Tolerance May Require Scaling to Ensure a Seamless Fit. I Found That Applying 101.01% Scale on X and Y Axes and 100% on Z Axis Yielded the Best Results. Update:...

Replacement part for GE Oven bottom drawer slider. Replacements are waaaaaaay over-priced ($35!). This is an improved (stronger) design than OEM. I also made the slider gap slightly narrower so the drawer does not have so much play up and down. ...

Christmas Yard Reindeer Swivel Replacement Part for animated, lighted Christmas deer sold at Home Depot. This crucial part links the motor to linkages responsible for swiveling the head. Printing on its side prevents supports from interfering with...

This part replaces the stock MDF extruder with a more durable and longer-lasting 3D printed version, designed to withstand heavy use over time. Please refer to the assembly instructions for information on where this piece fits into the overall...

I took charge of designing a replacement part that would not only restore connectivity but also fortify the horizontal landing leg to prevent future failures. Print Settings: Printer: Flashforge Creator Pro Rafts: None, actually - they don't...