the extra slide 3d models

remixed the tamper to add 20mm to the length at the tip remixed the tamper again and added 10mm to the top part of the plunger remixed the hopper to add 20mm in height to hold the plunger better and raised the surface the bellows rest on 20mm higher...

petg grill for the canister tunnel

Added stronger supports to the uprights as the model bends with the weight of the jewellery on it. ...Also adedd an updated base with compartments.

I liked the 5 version but not the tail, so here it is. ...thank you

Has the same size as the original hands. ...No supports needed.

Modified back side, without caps, plus version for the roof of the car.

Has the same size as the original hands. ...No supports needed.</p>

As the Cobra has a huge amount of power, the knoc needs to be re-enforced with a steel pin. King regards to the original designer of the knoc. ...You will need to hammer the pin in place.

This is a remix of the combustion lining part for the 3D printable jet engine, inspired from: https://www.thingiverse.com/thing:2441852 The top of the support has horizontal protrusions to fully support the otherwise unsupported part.

Print both and glue together with resin and cure with UV.The cap is scaled down of 0.05 to better fit without applying force.Be careful to remove the tank from vat as the resin will flow out.Be careful as once you remove the tank cap, the resin will...

I cut off a millimeter from the feet because they weren't flat on the printing surface, therefore the adhesion was poor or even non-existent

Thanks to marsellus2k for the original design. ...The only change I made was to increase the length to fit different bodies.

The slide stopper This useful 3d print prevents objective lenses smashing, scratching or damaging slides or themselves if they are too close to slides. ...This print stops all sizes of objective lens exactly 1mm away from the slide, preventing damage.

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

Stretched the back to add 4 mm so that the cover makes positive contact with the hard stops at the ends of my CR-10 V2 X axis. ...This prevents the extruder from running off the rail and gives predictable feedback for sensorless homing.

Here are the trays designed specifically for the 2019 Dune game, created to work seamlessly with the faction holders found on Thingiverse at https://www.thingiverse.com/thing:3940834. ...To optimize their functionality, consider scaling down the height...

I have lowered the overall height the legs will stand on by 12mm, and removed the slots for acrylic sheets from the original design. Print instructionsPrint 4 of these to add a third table to the bottom of a lack enclosure, for additional height. ... I...

When you go in to setup mode, it cycles through the on and off positions for each segment of the clock and you use the + and - buttons to set the correct positions. When you are done, the values are stored in the Arduino's EEPROM so they are there...

Specifically designed for this model, the rail attaches securely using the original screws that come with the firearm. To achieve optimum quality, print the rail with support and at a layer height of 0.1mm. ...You may need to drill a small hole for the...

Based on the outstanding NEMA 23 Holder by 6brueder, I discovered that the specific NEMA 23 motor I utilize is longer than the original design accounts for. ...As a result, I made adjustments to the original design to accommodate a 3-inch long motor -...

The inevitable future maintenance and repairs will be made easier with this addition, as the modder has had little luck with RC boats. All parts print without support. The top prints magnet holes facing up. ...The deck is printed as per the original...

I had trouble getting it to stay on the wall with just mounting tape. ...So I designed a little support that increases the area for the mounting tape. ... Can be added to an already finished model, and is well hidden.

I translated the original mount layout into OpenSCAD and incorporated several fresh mount options: calipers/scissors, hexagonal Allen wrench blocks, broader pliers, and pedestals to enable attaching a group of these to the 2020 beams forming the base...

Unfortunately the hole in the wall was too big for a standard size cover and the hole was going to be really annoying to fuss with. Needed an asymmetrical oversize cover. I uploaded the SketchUp file so that it can be adjusted to what you need. ...The...

The provided content is the outcome of a collaborative effort between myself and my friend, Mark Yousry, as part of our university assignment. ...We hope you enjoy it!

... hole significantly. Furthermore, I extended the length of the four retainer posts to ensure a more secure hold on the pi zero board. Additionally, I increased the indentation on the lid retainer rail to provide an even better grip on the lid itself.

Hi! ...This is an anal plug for big dimensions. The largest diameter is 55mm. The total height is 110mm. ...For Infill is sufficient 20 %.

*Make sure to rotate the back 90 degrees along the Y axis before slicing* Maybe the gaps in the base LHT-67 bother you aesthetically. Maybe you hate the LHT-71 but want something that looks a little beefier than the 67. Maybe you want to be able to...

This is a magnetic wool tile reminiscent of Settlers Catan, enhanced by the addition of sheep.

A well-crafted polygonal model, precisely sized to give an authentic depiction of the actual item.