thermacell butane refill adapter 3d models

see my file "Thermacell_Filler_v1" I would label this version as obsolete as the newer version is a stand-alone unit that utilizes the gasket on the cartridge this is an adapter for a standard butane tank to fill up thermacell cartridges. It isn't...

This is a thermacell adapter to refill a thermacell butane tank. First, you need to remove the one-way valve preventing you from refilling it. Instructions to do so are here: https://www.youtube.com/watch?v=mRjp-3PJuNQ Then, you buy a cheap butane...

Remixed it to minimize leak on Thermacell side and to make it fit the refill canister from "Biltema". Also included generic model with conical hole that should fit most (if not all) refill canisters. I glued my adapter to the refill canister using...

These are some butane lighter refill adapters/nozzles. The adapters/nozzles that came with the can of butane never fit my lighters quite right, so I made my own. I had the best results when they were printed with a 0.25mm nozzle. Note that there...

... mm drill and thread the Ronson M4.5 valve and insert some glue into the threads. You can fill up when the tube remains in the thermacell. (obviously turned off ;-) Wear safety goggles when filling! ... The protective hats are good to use then.

Holder for up to two refills for the Thermacell Rechargable Repeller models. Keeps refills upright. ... Make sure to print with openings facing up and no supports are needed.

Holder for up to two refills for the Thermacell Rechargable Repeller models. Keeps refills upright. Make sure to print with openings facing up and no supports are needed. Print Settings Printer Brand: Creality Printer: Ender 3 Supports: No Infill: ...

This is an adapter for a Butane Fuel Canister to fit lighters. It can be printed on a FDM printer or a SLA (Resin) printer. If printed by FDM, use 0.1mm Layer height and a Brim (Brim only on Outside ☑) There is a long (10mm shaft) and a short...

Customized version of https://www.thingiverse.com/thing:3672072 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3672072

Customized version of https://www.thingiverse.com/thing:3672072 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3672072

Customized version of https://www.thingiverse.com/thing:612709 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=612709

This nozzle adapter can be used to fill Butane Jet Lighters or Disposable Lighters using standard Butane Gas Canister Nozzle Use butane torch to heat the nozzle fitting side of the adapter then insert, it will create an airtight seal and you'll not...

This nozzle adapter can be used to fill Butane Jet Lighters or Disposable Lighters using standard Butane Gas Canister Nozzle Use butane torch to heat the nozzle fitting side of the adapter then insert, it will create an airtight seal and you'll not...

This adapter will adapt between a Sterno butane fuel cartridge and a little port on a creme brulee torch, once you can take off the cover to give it a little more space to squeeze in. ...Remember to hold it upside down so the liquid will travel into...

Slip on belt to hold filling adapters.Filament: TPULayer: 0.2 mm 

I have a bunch of butane cans for an old Campmate camping stove to go through before I upgrade the stove itself. But the plastic adapter from the can to the stove tube broke, so I made this replacement. ...

Butane molecule I recommend using glue I used rafts for hydrogens and supports for carbon Download and print all 3 parts once I used Slic3r program for print

For smaller flask the spout at the refill pack is too big. ... Adapter Refill pack M14x2 with sealing lip to M12x1.5 with Cover.

The Esun spools come in 2 parts. ...this adapter ring allows you to use refill filament with a 102mm diameter and 68mm width.

The cap can be used to seal the refill bottle back up without having to take the adapter off and put the original cap back on. ... https://a360.co/31XoVKh https://a360.co/2vy2wXL https://a360.co/320vEms https://a360.co/37raPBW ...

Adapter to make eraser refill made for electric erasers fit Pentel twist-eraser mechanical pencil. Fits for erasers 5 x 25mm that are commonly available for cheap from aliexpress. ... You might need to scale it up a bit depending on your printers...

I designed a little adapter to refill my DSG transmission according to VW specs. I happened to have a peristaltic pump laying around with an inner diameter of 4mm and outer diameter of 7mm. So I designed this adapter to fit the same tube as the pump....

It wasn't a problem to complete the change or to get the remaining part out but be careful to not put lateral force on the part during the oil change! Print instructionsCategory: Automotive Summary I designed a little adapter to refill my DSG...

Screw and nut for Fillamentum spool. ... You need to have an empty Fillamentum spool. The spool is cut in half with a saw. The new refill is placed and the spool is assembled with the help of a 3D printed parts nut and screw.

None of the adapters which came along with the gas cartridge fitted my kitchen gas torch, so I quickly modeled a working one in Fusion 360.Inner diameter base: 3mmInner diameter torch: 2.25mmModify the Fusion 360 sketches to your needs.

This adapts a 5mm air compressor blower nozzle to a 3.3mm aerosol can nozzle. It prints in less than 10 minutes and works seamlessly. ...Leave comments if you have a different size and want me to make it tailored to your needs.

With this adapter, you can replace LAMY M63 refill with following refills for LAMY rollerball pen.*Pentel LRN4, LRN5, LRN7*UNI UMR-85N, UMR-87

Ender 3 100% infill Generic PLA Had to sand a little to get to fit right

This is a handy adapter to refill the Quip brand travel size toothpaste tube using the normal size flip-cap tube. This may fit other tubes: the threads are 15x1.5mm ISO on one side; 11x1.5mm on the small side. To refill, remove the cap from the...

Adapterring for 1 KG Refillcoils. 8x M3 screws and nuts are required. Printed at 0.2mm layer height. Sacrificial support on the top holes but minimal support is needed.