thermacell refill adapter 3d models

This is a thermacell adapter to refill a thermacell butane tank. First, you need to remove the one-way valve preventing you from refilling it. Instructions to do so are here: https://www.youtube.com/watch?v=mRjp-3PJuNQ Then, you buy a cheap butane...

Remixed it to minimize leak on Thermacell side and to make it fit the refill canister from "Biltema". Also included generic model with conical hole that should fit most (if not all) refill canisters. I glued my adapter to the refill canister using...

Customized version of https://www.thingiverse.com/thing:3672072 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3672072

Customized version of https://www.thingiverse.com/thing:3672072 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3672072

... mm drill and thread the Ronson M4.5 valve and insert some glue into the threads. You can fill up when the tube remains in the thermacell. (obviously turned off ;-) Wear safety goggles when filling! ... The protective hats are good to use then.

Holder for up to two refills for the Thermacell Rechargable Repeller models. Keeps refills upright. ... Make sure to print with openings facing up and no supports are needed.

Holder for up to two refills for the Thermacell Rechargable Repeller models. Keeps refills upright. Make sure to print with openings facing up and no supports are needed. Print Settings Printer Brand: Creality Printer: Ender 3 Supports: No Infill: ...

see my file "Thermacell_Filler_v1" I would label this version as obsolete as the newer version is a stand-alone unit that utilizes the gasket on the cartridge this is an adapter for a standard butane tank to fill up thermacell cartridges. It isn't...

Customized version of https://www.thingiverse.com/thing:612709 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=612709

For smaller flask the spout at the refill pack is too big. ... Adapter Refill pack M14x2 with sealing lip to M12x1.5 with Cover.

The Esun spools come in 2 parts. ...this adapter ring allows you to use refill filament with a 102mm diameter and 68mm width.

The cap can be used to seal the refill bottle back up without having to take the adapter off and put the original cap back on. ... https://a360.co/31XoVKh https://a360.co/2vy2wXL https://a360.co/320vEms https://a360.co/37raPBW ...

These are some butane lighter refill adapters/nozzles. The adapters/nozzles that came with the can of butane never fit my lighters quite right, so I made my own. I had the best results when they were printed with a 0.25mm nozzle. Note that there...

Adapter to make eraser refill made for electric erasers fit Pentel twist-eraser mechanical pencil. Fits for erasers 5 x 25mm that are commonly available for cheap from aliexpress. ... You might need to scale it up a bit depending on your printers...

I designed a little adapter to refill my DSG transmission according to VW specs. I happened to have a peristaltic pump laying around with an inner diameter of 4mm and outer diameter of 7mm. So I designed this adapter to fit the same tube as the pump....

It wasn't a problem to complete the change or to get the remaining part out but be careful to not put lateral force on the part during the oil change! Print instructionsCategory: Automotive Summary I designed a little adapter to refill my DSG...

Screw and nut for Fillamentum spool. ... You need to have an empty Fillamentum spool. The spool is cut in half with a saw. The new refill is placed and the spool is assembled with the help of a 3D printed parts nut and screw.

None of the adapters which came along with the gas cartridge fitted my kitchen gas torch, so I quickly modeled a working one in Fusion 360.Inner diameter base: 3mmInner diameter torch: 2.25mmModify the Fusion 360 sketches to your needs.

This adapts a 5mm air compressor blower nozzle to a 3.3mm aerosol can nozzle. It prints in less than 10 minutes and works seamlessly. ...Leave comments if you have a different size and want me to make it tailored to your needs.

With this adapter, you can replace LAMY M63 refill with following refills for LAMY rollerball pen.*Pentel LRN4, LRN5, LRN7*UNI UMR-85N, UMR-87

This is a handy adapter to refill the Quip brand travel size toothpaste tube using the normal size flip-cap tube. This may fit other tubes: the threads are 15x1.5mm ISO on one side; 11x1.5mm on the small side. To refill, remove the cap from the...

Adapterring for 1 KG Refillcoils. 8x M3 screws and nuts are required. Printed at 0.2mm layer height. Sacrificial support on the top holes but minimal support is needed.

stand for a hand held thermacell anti mosquito device There is a tab at the back of the thermacell which this design does not handle. ...The design should have a slot at the back.

Simple clip for Thermacells that don't come with a belt clip Printed in PETG 40% infill Printed on side with supports Update: Added larger fillets at the clip to Thermacell connection point.

Quick and dirty holder for Thermacell Portable Mosquito Repeller, made for MR450. ... MR150 do fit, and looks like MR300 do fit also.

Adapter to fit a D1 size ink refill into a Schmidt P8126 shape.

This adapter allows you to reuse the 3D Solutech spool thing for eSun refills. ...

This is adapter to reuse Bambu spools with Refill filament like Fibelogy

With this adapter you can use a Pilot G2 pen and Pilot G2 pro pen with a MONT BLANC Refill Ballpoint Pen instead of the original gel ink refill. ... Happy writing ;-)

Hi, I made this adapter to use the refill filament from esun on the Bambu refill spools, made these with snug tolerances so when using the AMS the filament doesn't spin freely and cause an issue.