thingiverse hypercube evolution 3d models

I found the original at Thingiverse (https://www.thingiverse.com/thing:3036241) but the "hook" to attach the strains to was a bit to flimsy and weak for me (actually broke two times on two models while attaching the strains). So I removed the hook,...

Remix of https://www.thingiverse.com/thing:3694704, my issue with the original design was that the BLTouch was positioned a bit too far forward from the right heater, so I made some adjustments and flattened the top to improve the overall structure.

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

... two of these flags on each side to precisely level the bed and perfectly synchronize the two z-motors. The knob and mount for the optical endstop are direct adaptations from "tessarin's" brilliant design: http://www.thingiverse.com/thing:3272343

I build this great electronics_enclosure by melnikod https://www.thingiverse.com/thing:2761069 but needed a a mount for my display. Its just a very quick design, it fits - beauty is on a different topic. Its the display on the right in the photo.

Thanks Scott for this amazing find on Thingiverse - https://www.thingiverse.com/thing:2254103! This part is super helpful in setting up my Y-carriage and may even boost X/Y/Z carriage accuracy. To get the most out of it, I need to print two copies of...

I crafted this outstanding electronics enclosure by melnikod, accessible at https://www.thingiverse.com/thing:2761069, but I required a mounting system for my display. It's simply a quick design that fits, with beauty being a separate issue...

As it is a modular design (https://www.thingiverse.com/thing:2777161), the backplate does not have to be reprinted again. Height is adjustable to create the correct distance between the nozzle and the bottom of the platic part of the sensor (about...

https://www.thingiverse.com/thing:2916495 Edit: I've added the 4x205mm plate. Cura estimates it will take ~419g and 2d 04h 44min to print at 35 mm/s. Fun times! And yes, I have the system on an APC 1000 for if the power goes out. I'm using...

A small case developed by Pomaser caught my eye - "Logitech C270 Webcam Cover Replacement (with GoPro Mount)" on Thingiverse (https://www.thingiverse.com/thing:3748407). Instead of the original casing, I opted for this one. Design Concept I didn't...

... can see in the screenshot, the nozzle-to-BLtouch distance is crucial - mine comes in at 35 mm on the X-axis and 8 mm on the Y-axis. This setup will be perfectly matched with the cooling system found here: https://www.thingiverse.com/thing:3512817

Inspired by DarthOctane's brilliant idea (https://www.thingiverse.com/thing:2353414), I made some tweaks to make it perfect for the PC-Rubberfeet, which are super affordable here or available elsewhere:...

... nut inserts) along with an extended X flag. Warham has graciously shared various versions of his design to accommodate different rod configurations on Thingiverse - feel free to visit https://www.thingiverse.com/thing:2469902 for more information.

... should be glued onto the carriage Y. I utilize compact endstops on the Y-axis (https://www.thingiverse.com/thing:3236443), which work well for me, and I intend to continue using them, attaching a flag either to the carriage or bearing cover.

A Remix of sschueller's Linear Rail System (https://www.thingiverse.com/thing:2839395) using: 2 x MGN12H for Y Gantry 1 x MGN15H for X Gantry Remix it to use direct drive and M3 nuts and bolts instead of Brass Inserts and Dowel Pins 1) The motor box...

Spool_Holder_Clamp_Top/Bottom -- I'm using this with a length of M8 threaded rod and these https://www.thingiverse.com/thing:2532403 spool holders. Tension_O_Matic -- The screws on X carriage are good for fine-tuning belt tension, as well as...

Requires:2x M2.5 hex nuts.2x M2.5x8mm screws.Change logFrom V1:Rotated the extruder and printhead so that they both face forward, which allows for use of the Bondtech LGX FF 5015 fan shroud and makes swapping nozzles or servicing hot end easier.Added...

Remix From Thingiverse - 3D Printed Guitar Pick Holders with a Twist This innovative design by maker [Maker's Name] takes the original guitar pick holders to new heights with its sleek, modern aesthetic and clever functionality. The remix adds a...

The 12864 Case, a sleek and modern enclosure for your computing needs, has been remixed from the original design found at Thingiverse under the identifier 3475522. This remix builds upon the foundation of the original creator's work, offering a fresh...

Update 2/28/2018 I've implemented a decent cable management system, thanks to https://www.thingiverse.com/thing:11978 for a cable chain on the Y-axis and a standard cable loom. I uploaded a new Y endcap and two loops for the cable loom, which...

Here's a rewritten version of the text: Extruder Mount with PiBot Optical Reflection Endstop. ... For cooling, use the 40 mm fan duct from this build on Thingiverse: https://www.thingiverse.com/thing:2305218. (c) Hypercube-Evolution.de

Pes para aumentar perfil 3030 daa Hypercube Evolution c/ furo roscado 1/4

I edit a fully functional F3D HyperCube Evolution electronics enclosure to be completely customizable.

... because the Cooling Fan clashes with the cable chain. ... Cable Chain: Check out this design at https://www.thingiverse.com/thing:2823973. HyperCube Evolution: Find more details about this project here: https://www.thingiverse.com/thing:2254103

Human Designed Hypercube Evolution T12 Z Nut Bracket. A Personalized Version of the Original Design on Thingiverse (https://www.thingiverse.com/thing:2903163). ... Crafted with Customizer, a Powerful Tool for 3D Printing Customization...

Adapter created for BLTouch use. ...Modified now to work effectively with M2 hole compatibility.

The extended duct allows for a downward airflow onto the piece.

!!! ALPHA VERSION!!! To-Do List: * Mount a high-quality LCD display on the panel using GLCD or MKS TFT32 technology. * Integrate a robust RAMPS/RUMBA board mounting system. ...* Design and fabricate a secure NES-350-12 power supply mounting section.

Work in Progress: Refining the Gimble Stepper Mount to Optimize Cable Dynamics. To alleviate cable stress, I'm currently working on modifying the gimble stepper mount. A video demonstrating this modification can be found at...

Hallo hier ist mein Remix aus verschiedenen Projekten. Fusion360 Link https://a360.co/2MTRxyb (Es Werden sich noch mehrere Teile ändern, Y Achse, Endstop Z und Y u.s.w.) Angefangen mit CubeAnet. Weil dort paar Sachen mir nicht passten...