traxxas slash 2wd front bulkhead 3d models

I made this 0 degree bulkhead to make my slash into a drag car. Works great! ...Print flat with supports touching buildplate for best results!

Front Axle for Traxxas Slash 2WD Off-Road Short Course Truck.

The is a kitbash of the original. ...I made the front decks thicker to better take a hit. to get the densest deck print on edge into z territory. ... I will be designing a break away system that will self correct after impact.

Update 5/12/2015: Spent some quality time bashing with my Traxxas Stampede, resulting in a front A-Arm mount breakage. Repaired it by re-printing the part in a new direction and fortunately didn't encounter any issues this time around. I'm convinced...

I designed this brace to fill in the space in the STRC Front hinge pin in the Front bulkhead Suspension Hinge Pins Traxxas 2wd rustler and slash this is to be used for a temporary part until it can be replaced with aluminum brace. if you wish to...

Printed for a Traxxas Slash 2wd. The 4x4 setup is a distinct configuration. This one doesn't utilize bushings or bearings, which may cause it to wear out rapidly. However, it appears to hold up remarkably well nonetheless. ... Thanks for the...

I adjusted the size to fit a 2wd Slash. The fit might be a little tight, but over time, it will break in. ...Fill at 100% to ensure strength.

All of the stands I have found are for the Traxxas Slash 4x4, so I took it upon myself to design a simple stand for my Slash to keep the wheels off the ground when in storage on the shelf. For assembly, you need the following: (8) M3x10-12mm screws....

All of the stands I have found are for the Traxxas Slash 4x4, so I took it upon myself to design a simple stand for my Slash to keep the wheels off the ground when in storage on the shelf. For assembly, you need the following: (8) M3x10-12mm...

THIS IS A MODIFIED VERSION OF THE TRAXXAS PART 3736. IT'S MUCH THICKER THAN THE ORIGINAL PART AND I BELIEVE IT'S ALSO MORE DURABLE, EVEN WHEN PRINTED WITH PLA, THANKS TO THIS EXTRA THICKNESS. ... THERE ARE ACTUALLY LEFT AND RIGHT PARTS, AS THE THICKER...

Front bulkhead (2530) for a variety of different Traxxas vehicles (Bandit, Slash, Stampede, Rustler, SRT). I have fit this up and confirmed it to be compatible (dimensionally) with the original SRT double deck chassis. Arms have been confirmed to...

This is a straightforward flat ESC Mount designed to seamlessly fit into the stock ESC location on both the stock Traxxas Slash 2WD Chassis and the Low Center of Gravity (LCG) Chassis. It might also work with other models that utilize the XL-5 ESC,...

This is an experiment to extend the wheelbase of a Traxxas Slash 2WD to fit Arrma Infraction or Felony bodies. It makes the wheelbase 76 millimeters (3 inches) longer than stock. It is designed around the Slash LCG chassis, and I have no idea if it...

This is a simple wheelie bar I designed for my Traxxas Slash 2wd VXL as it spent far too much time on its roof! In addition to the printed parts you will need the following parts: 2x 625 bearings 2x M5x20 countersunk head bolts 2x BS210 O-rings 4x...

This is the first of many print sets for a 2wd Slash down-force system. Suitable for both drift and drag cars. When the whole system is installed your car should pull itself down and make the car squat as speed increases. This fits with and without...

Just take off the bumper and use the 2 screws from the front to attach the chassis mount. The little oval part that it attaches to is a bit bouncy and may be springy enough for you. But, if you want more springiness and are going to use a winch, I...

traxxas slash 2wd rear bumper mount compatible with asciencepotato's 4wd bumper. ...It's a little fragile, so please drive carefully.

I've printed several versions with varying levels of success. The first version worked well without needing much filing, but I had to file the support angles on subsequent versions to clear the shocks and ensure proper alignment. A touch of filing at...

Body Mount Extension as Add-On to the original Body Mount of the Slash 2WD to fit the Proline F150 1979 body in the front. ... Built with Tinkercad.

The front section of the Traxxas Slash 2WD model awaits your attention, pending the first step in bringing it to life – printing it. Has anyone attempted this print? If so, please share the results. Print with 100% Infill Preparation Print...

I designed these mud guards for a Traxxas Slash 2wd High center of gravity chassis to keep the dirt out of the chassis. It uses the holes from the nerf bars so you will need 4 screws that are a bit longer to replace the ones from the nerf bars. ... ...

This design is tailored specifically for a Traxxas Slash 2WD, allowing users to reverse-mount the transmission for improved center of gravity and cornering capabilities. Alternatively, it can be installed in its original configuration. ...The design's...

This is a Traxxas Slash 2wd LCG Chassis - Sidewinder SCT ESC Holder Bracket and FS-RG3E Receiver Holder. The Castle Sidewinder 3 SCT needs two to three twenty-five millimeter screws to keep it in place securely. ... The FLYSKY FS-RG3E requires one...

It's also likely compatible with other 2wd Traxxas models, but some modifications will be necessary to get it to fit properly. The design draws inspiration from the new clip-on style straps featured on the Traxxas 4TEC 2.0 and TRX4. To install this...

However, it may also work with other 2wd Traxxas models after some modifications have been made. The design of this strap is based on the new style of clip-on straps found on the Traxxas 4TEC 2.0 and TRX4. To make use of this strap on your car,...

This is the Front Caster Block for a Traxxas Slash 2WD, Bandit or Rustler. Print them if you break one... PLA Holds up okay in mid-temperature and cold. I use PLA for normal racing conditions. I raced for 1 hour accident-free with no breakage. I...

I designed a simple chassis saver for my Traxxas Slash 2wd with High Centre of Gravity chassis. The original design was made by Proline a few years ago to address the weak point where the transmission bolts to the chassis. However, when Proline...

wheelie bar for traxxas drag slash use m3x16mm screws these could be used for show or as templates to fit bodies

After hours of precision measurement and meticulous design, I created four test prints that led me to develop a brand new front bumper bar for the 1:10 scale Traxxas Slash 2wd. This custom part utilizes the original screws and mounting position,...

Mounts right in front of the receiver case/antenna. Note, it will block the antenna. I use a FrSky reciever now so don't use the stock antenna. I had to cut away much of the driver's side plastic to free it up for a good view but it works pretty...