traxxas slash 2wd parts 3d models
544569 3d models found related to traxxas slash 2wd parts.thingiverse
I use this with the low gravity kit for the Traxxas Slash 2WD. I start by screwing the longest chassis pin in at the back end of the car (backwards from Traxxas), and start the shorter wheel pin at the front end of the car (same as Traxxas). This...
pinshape
This is the Front Caster Block for a Traxxas Slash 2WD, Bandit or Rusler. Print them if you break one... PLA Holds up ok in mid Temp and Cold. I PLA is fine for normal racing conditions. I raced for 1 hour accident free with oit breakage. They...
thingiverse
Printed for a Traxxas Slash 2wd. (The 4x4 setup is different) This one doesn't use bushings or bearings, so it might wear out quickly. Seems to hold up pretty well though. Thanks, Enjoy! ...
thingiverse
I adjusted the size to fit a 2wd Slash. The fit might be a little tight, but over time, it will break in. ...Fill at 100% to ensure strength.
cults3d
All of the stands I have found are for the Traxxas Slash 4x4, so I took it upon myself to design a simple stand for my Slash to keep the wheels off the ground when in storage on the shelf. For assembly, you need the following: (8) M3x10-12mm screws....
thingiverse
All of the stands I have found are for the Traxxas Slash 4x4, so I took it upon myself to design a simple stand for my Slash to keep the wheels off the ground when in storage on the shelf. For assembly, you need the following: (8) M3x10-12mm...
thingiverse
This is a simple flat ESC Mount that fits in the stock ESC location on the stock Traxxas Slash 2WD Chassis and the LCG Chassis. It might fit other models that use the XL-5 ESC because that's what these holes line up with. The plate is 55mm x 55mm. I...
thingiverse
This is a simple wheelie bar I designed for my Traxxas Slash 2wd VXL, as it was spending far too much time on it's roof! In addition to the printed parts you will need the following parts - 2x 625 bearings 2x M5x20 countersunk head bolts 2x BS210...
thingiverse
This is an experiment to extend the wheelbase of a Traxxas Slash 2WD to fit Arrma Infraction or Felony bodies. It makes the wheelbase 76 millimeters (3 inches) longer than stock. It is designed around the Slash LCG chassis, and I have no idea if it...
thingiverse
This is the first of many print sets for a 2wd Slash down-force system. Suitable for both drift and drag cars. When the whole system is installed your car should pull itself down and make the car squat as speed increases. This fits with and without...
thingiverse
The little oval part that it attaches to is a bit bouncy and may be springy enough for you. But, if you want more springiness and are going to use a winch, I would suggest using a 3 cm spring between the mount and plow. (If I find that it becomes a...
thingiverse
traxxas slash 2wd rear bumper mount compatible with asciencepotato's 4wd bumper. ...It's a little fragile, so please drive carefully.
cults3d
Maybe it can fit on the other 2wd Traxxas as well with some modifications. It is based on the new style of clip on straps presented on the Traxxas 4TEC 2.0 and TRX4. The only modification required to the car is enlarging the hole where the hexagonal...
thingiverse
Maybe it can fit on the other 2wd Traxxas as well with some modifications. It is based on the new style of clip on straps presented on the Traxxas 4TEC 2.0 and TRX4. The only modification required to the car is enlarging the hole where the hexagonal...
thingiverse
I designed these mud guards for a Traxxas Slash 2wd High center of gravity chassis to keep the dirt out of the chassis. It uses the holes from the nerf bars so you will need 4 screws that are a bit longer to replace the ones from the nerf bars. ... ...
thingiverse
This is designed for a traxxas slash 2wd it allows you to mount the transmission backwards for better centre of gravity and cornering ability but you can also mount it stock. ...this was designed to be cut out of aluminium but can also be laser cut out...
pinshape
This is a Traxxas Slash 2wd LCG Chassis - Sidewinder SCT ESC Holder Bracket and FS-RG3E Receiver Holder. The Castle Sidewinder 3 SCT with phan will need 2 - 3x25mm to hold it in place. ... The FLYSKY FS-RG3E will need one 3x12mm and a little shoe...
thingiverse
This is a very simple chassis saver I designed for my Traxxas Slash 2wd with High Centre of Gravity chassis. Proline used to make these a few years ago to eliminate the weak spot where the transmission bolts to the chassis. Unfortunately, when...
thingiverse
Body Mount Extension as Add-On to the original Body Mount of the Slash 2WD to fit the Proline F150 1979 body in the front. ... Built with Tinkercad.
cults3d
wheelie bar for traxxas drag slash use m3x16mm screws these could be used for show or as templates to fit bodies
thingiverse
I made this 0 degree bulkhead to make my slash into a drag car. Works great! ...Print flat with supports touching buildplate for best results!
thingiverse
Note again, all of the holes line up nicely, but I have not printed and tested the V3 parts as uploaded! UPDATE for V4... Maybe I'm done, maybe not. I just uploaded V4 - I got the big bore shocks and needed a bit more space so I extended the...
youmagine
all parts have been heavily tested and abused on a few slashes. some parts are better printed in certain materials, the shock guards and bumper work very well in nylon for example.**some of these parts are now outdated. ...see my other designs for the...
thingiverse
I designed this brace to fill in the space in the STRC Front hinge pin in the Front bulkhead Suspension Hinge Pins Traxxas 2wd rustler and slash this is to be used for a temporary part until it can be replaced with aluminum brace. if you wish to...
cults3d
These are some simple spacers to raise the body mounts on a 2WD Traxxas Slash to accept a Ford Raptor body. ...Learn more about the process at www.RCDetails.ca!
thingiverse
This is a 73t 46p spur gear for Traxxas Slash 2WD. It should work with a 23 tooth pinion or larger. I never used it yet so please leave me a comment or like if this works. ...Thanks!
thingiverse
These are some simple spacers to raise the body mounts on a 2WD Traxxas Slash to accept a Ford Raptor body. ... Learn more about the process at www.RCDetails.ca!
thingiverse
This is a Traxxas Slash 2WD 1/10 model 64t (64 teeth) spur gear. I plan to use it with the 28 tooth pinion gear I just posted. It will not work with the 23 tooth pinion or lesser toothed pinion gears because it is smaller. This is not based on any...
thingiverse
Traxxas Slash 2wd Body Mounts 18mm 20mm Support is optional to print smoother circular body holder section, raft can be also used to stabilize prints. I used this on my RJ Speed Late Model Stock body, body needs to be lowered, original body...