two point discrimination tool 3d models

Avoid lifting and warped prints!There is a small amount of support needed - "for support enforcers only."Under the elevator shaft on the Middle Floor and Top Floor.The elevator door on the base floor.Increase the size of your “Dice Tower - Building...

The 3D printing model's chosen scale is 1/34 for the FFF/FDM version and 1/68 for the DLP/SLA/SLS version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 62 parts;- A printed model is 191 mm tall, 397 mm wide, 719 mm deep;- Assembly...

The 3D printing model's chosen scale is 1:34 for the FFF/FDM version and 1:68 for the DLP/SLA/SLS version.VERSIONS' SPECIFICATIONSFFF/FDM 2.0 version features:- Contains 30 parts;- A printed ship is 271 mm tall, 170 mm wide, 368 mm deep;- The updated...

After all, the "PSU attachment" is fixed to the same frame as the other two screws, so I don't think it is necessary to use it, but I put it on just in case. If you are concerned about it, please remix the screws so that they are attached to a...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

The 3D artist made sure to carefully outfit the two-pilot cockpit and the two-storeyed cabin that is known to carry up to 40 troopers to their deployment site. Various hatches and lids all over the body of this destructive weapon conceal the...

The two elaborately detailed donor cars stacked on top of each other rest on immense tractor tyres that elevate them above the ground and represent the militant Colonel's authority. So don't miss out on the opportunity to 3D print an addition to your...

The 3D printing model’s chosen scale is 1:350 for the FFF/FDM version and 1:700 for the DLP/SLA/SLS version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 50 parts;- A printed model is 152 mm tall, 416 mm wide, 312 mm deep;- There is...

“The hulking monstrosity on the ground” is most known for its nearly indestructible Kaiser Blades - two pairs of scythes that easily slice through most even armour-clad substances. Ultralisks possess extremely thick carapace and it even may seem that...

The model features the craft’s trademark three wings: a stationary dorsal stabiliser and two articulated flanking side wings. The 3D printing Lambda-class shuttle is heavily armed with a pair of forward-facing double blaster cannons, two wing-mounted...

For those customers who have already purchased the Treebeard figurine or are planning to do so, every version of the Merry Brandybuck model comes in two variants to choose from - an independent static figurine (marked “Stand” in the “Source files”...

The windows on the driver compartment viewport are provided as two separate files to be printed with the transparent filament. The headlights and “parking lights” holes are made hollow for you to introduce LED wiring if willing. Moreover, the scale...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

The 3D printing model's chosen scale is 1:400 for the FFF/FDM version and 1:800 for the DLP/SLA/SLS version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 42 parts;- A printed ship is 133 mm tall, 480 mm wide, 469 mm deep;- Assembly...

Both versions are to be identically assembled to the body of the bike;- The assembly of the front and rear shock-absorbers requires 2 regular ball pen springs and additional "pins" made out of short pieces of regular 1.75mm filament;- Rotation of the...

The 3D printing model’s chosen scale is 1:32 for the FFF/FDM version and 1:64 for the DLP/SLA/SLS version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 26 parts;- A printed model is 183 mm tall, 134 mm wide, 305 mm deep;- Tender's...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

The 3D printing Sparrow figurine has his long hair dreadlocked and customarily wears his goatee in two braids. The author of the model made sure to include Jack’s signature tricorne hat, bandanna, and lots of intricate beads and ancient coins that...

In order for you to achieve the cleanest 3D printed result possible, Voltron’s Blazing sword and the back wings were split into two halves for their convenient placement on the build plate. All assembly parts are provided in STL files in recommended...

In order to ensure the cleanest 3D printed result, Otachi’s tongue was extracted from the beast’s mouth, while the two parts of Kaiju's signature crest were cut off as well.All assembly parts are provided in STL files of FFF/FDM version in...

Or click Download once on the file heisenberg.rar My some other things:                       ...

... each time. My some other things:                                

# Addtional Hardware Needed: - 4-40 Thread Size Screws (https://www.amazon.com/gp/product/B00GDZEM9Q/) - USB-C Extender (https://www.amazon.com/gp/product/B0BPSNZVQ2/) # Devices Needed: - Gamesir X2 Pro...

... time. My some other things:                                

... hang of it, but I think there's been some mistake. This is a text-based conversational AI, not a content generation tool. ...You can have a conversation with me, ask me questions, or provide information on a topic, and I'll do my best to assist you.

Or click Download once on the file Unicorn.rar My some other things:                       ...

... the site is broken and no one is going to fix it. ...Download files one at a time by clicking Download each time. My some other things:                                

... My some other things:                                

... My some other things:                                

... each time. My some other things: