ubitx enclosure 3d models

... the profiles 6. Mount the distance pieces 7. Attach the nylon cord in order to hang the lamp on the wall using a nail. ## Planned Updates I am planning to design a small enclosure for the arduino. ...I will add the files as soon as this is done.

FAQ: http://www.thingiverse.com/shivinteger/about Generating Attributions log: Thing Title : Miniature Car Chassis Holder Thing URL : http://www.thingiverse.com/thing:34114 Thing Author : integershiv Thing Licence : Creative Commons - Attribution -...

... but I had a heck of a time with it lifting from the print bed. Even with a 15mm brim it still ended up lifting so I think this would print better in an enclosure. ...The top portion prints easy enough, but some supports are useful when using PETG.

This is just a small enclosure for a 5-24V boost convertor i purchased off of Amazon. They are pretty common and have used these in the past and thought it might be nice if there was a protective case for it.</p> <p>The lids do somewhat snap on and...

**Print Settings:** * Printer: Tevo Tarantula * Rafts: No * Supports: No * Resolution: 0.2mm or less * Infill: 20% or more **Post-Printing:** This design offers several benefits, including: * A better enclosure for the LCD panel * Uses stock buttons...

**Print Settings** * Printer: Monoprice Maker Select V2 * Rafts: No * Supports: No * Resolution: .1 * Infill: 100% concentric **In Use** Tiny C-clips are used to secure a circuit board mount within an enclosure. ... **Updates** February 6, 2017 -...

This shouldnt be a problem because you will not be constantly removing the bolt to the enclosure. You may be able to use a file to allow the M8 bolt to fit through the hole. 2. If required, drill out the holes on the cover plate with a 3mm drill...

This is a remix of lordwimseys' enclosure for the MKS mini 12684 LCD to mount it to vertical beams of 2020 profiles. The current version is debugged and finalized. Two versions are available. One is for vertically mounting the other for mounting to...

Note that it's not a full replacement for the original case, but instead replaces the white enclosure, designed to be fitted with the original back plate. The wall mounting plate can also be used with this new case. **Note**: these ST motion sensors...

When I first saw Kagarov's Ultracompact chess set, I knew I want to print it and give it as a small wedding gift to my friend. https://www.prusaprinters.org/cs/prints/28518-ultracompact-set-castlechess But it needed some kind of enclosure or box to...

The model includes an exterior enclosure, canopy, Burger King signs, rooftop mechanical units on curbs, textures, doors and windows, sidewalks, curbs, parking stripes, handicap sign and pavement striping, grass, light fixture, Burger King drive-thru...

Update 8/24/2017: Added a version with SD card access hole as per the feedback (PhatDacSD.stl). This is an enclosure that just fits Pimoroni Phat Dac available at @Adafruit attached on a Raspberry Pi Zero W with the included GPIO header. The lid can...

This one works almost with no stringing and perfect. Print instructionsUnassociated tags: anti vibration, Lack enclosure, Prusa MK3 Category: 3D Printer Accessories Print Settings Printer Brand: MK3 Printer: Prusa i3 Rafts: No Supports: No...

Inspired by the many air filtration systems, I wanted to design my own that incorporated easy-to-find respirator cartridges, an 80mm fan, and my Ikea Lack enclosure. I used these [respirator...

The sensor and the enclosure are very lightweight, and the incoming filament keeps it upright on my Ender3. You'll need to run the cabling to your printer/raspberrypi yourself. I extended mine with some spare network cable using good old fashioned...

2 front acrylic doors and hinge transparent acrylic top cover and acrylic side panels provides full enclosure for internal heating needed filaments (like ABS). Duet 3D electronics and screen is situated in a custom tiltable 3d printed case below.The...

I made this custom subwoofer enclosure to replace the standard one on my Logitech speaker system for PC. The hole for the speaker was designed specifically for a 4-inch woofer from my Logitech system. Since I'm not an audio engineer, I can't confirm...

It was also not a fan of the wire brush it used, plus it was a pain to put on and remove (since my CR-10S is in an enclosure). So, I took that design as inspiration for an adjustable version that should fit any printer with about 70mm spacing between...

The hinge attaches an Acrylic door to a wood frame, forming part of a protective enclosure. Since it utilizes existing bolt holes, you won't need to drill any new holes. It secures at the top of the frame using three pre-existing bolt holes. To...

This is an enclosure for a Raspberry PI and a 5 inch display. The opening in the back allow for the addition of a Hifiberry Digi+ (pro). This is a perfect box for a Volumio audio streamer. The display I used is this one (not affiliated): ...

By integrating a reliable and accurate thermometer and hygrometer into the dry box setup, users can gain valuable insights into temperature and humidity levels within the enclosure. This knowledge enables them to identify potential issues before...

In my printer enclosure I have my filament mounted up and behind the printer. This works great by flipping my spools to go under rather than over. I designed this for my Prusa Mk3 Full Bear upgrade. ...It should work with most v-slot printer setups.</p>...

I tried out this great design from Ernie34 at https://www.thingiverse.com/thing:2656493 and found that I didn't have quite enough room for my electronics in the other side of the enclosure (The Kulp K8-B is fairly tall). This design had quite a bit...

All parts except for the LCD enclosure are sized under 100mmx100mmx100mm, making them producible on smaller low-budget printers like Hobbyking's Mini Fabricator V2 and similar. This means you can create this large-scale, high-output printer using...

the idea was born to be able to have the filament outside the printer in this way you can have the printer housed inside a closed enclosure to print heat-sensitive materials. it is assembled by pieces, with rubber hammer to pressure, the wheels...

Print enlarged to allow for ABS shrinkage - I used 100.5% as the Robox has excellent bed heating and enclosure which minimizes shrinkage. How I Designed This CAD Sketchup - I designed the circular parts first and "pushed" them to get the right...

B8 stick that was a part of the v1 package is now fully functional and has moved to a separate package (https://www.thingiverse.com/thing:2918906) IKEA GUNDE CHAIR (optional): http://www.ikea.com/us/en/catalog/products/00217797/ simchair IKEA GUNDE...

This is a security camera enclosure designed specifically for the Raspberry Pi Zero W in combination with a Raspberry Pi NoIR camera module. You can easily find these camera modules on AliExpress, Ebay, and other online marketplaces by searching for...

I run my filament a little hotter than recommended for ABS but it seems to make the layers stick together better (with the help of a cheap enclosure build). I will upload pictures soon to update the project as well as add another "Thing" to hold...

... The entire box weighs about 210g when filled with 2x18650 Panasonic batteries, the plastic enclosure, electronic board, and belt clip. The electronic board is a portable mobile power supply that supports two voltage outputs: 3V / 1A and 5V / 2.2A.