ultibots d300vs plus 3d models
55264 3d models found related to ultibots d300vs plus.thingiverse
Simple adapter plate designed specifically for the D300VS+ printer, tailored to work seamlessly with the Dii Cooler. https://www.thingiverse.com/thing:1025471 The advantages of this adapter plate are numerous. Better cooling performance compared...
cults3d
Why? Just for fun ;) Design: The scale factor is 0.6. Since the needed absolute offset is not scale able, some parts needed to be adjusted after scaling. ...That's why all 5 models are uploaded.
thingiverse
... with a 300mm bed in mind, and can accommodate beds up to 6mm thick. In addition to this useful tool, you may also be interested in the following items: * hardrocker's V-Slot Power Supply Mount * sreid55's Ultibots D300VS Bottom corner plates
prusaprinters
Still was having issues with getting good bridges and overhangs at fast printing speeds so I decided to just go with brute force cooling with two 5015 fans . Works like a champ, can work too well. Make sure your hot end has a sock and you...
thingiverse
I was still struggling with achieving good bridges and overhangs at high printing speeds, so I opted for brute force cooling using two 5015 fans instead. The setup performs exceptionally well, but it can be too effective in some cases. To get the...
thingiverse
This is a ball-cup arm upgrade set for the Ultibots D300VS, designed for use with Trick Laser/SeeMeCNC fixed-width barbells and Trick Laser Ball-Cup Arms. It also works with the stock Ultibots micro extruder. This set can be used on other Kossel...
thingiverse
This mounts an E3D Titan Aero onto an Ultibots D300VS. It may also work on a K250VS with a small stepper motor. The spacer is designed for small steppers with short shafts that cannot use the standard E3D spacer. Simply jam it into the heatsink...
thingiverse
The Ultibots 24V to 12V converter can be mounted on the MendelMax 1.5+, a kit and set of printed components that can be bought from their official website, www.ultibots.com.
thingiverse
The fan duct assembly is designed for the stock Ultibots D300VS Micro Extruder and E3D V6 hotend. The internal geometry of the parts duct features air guides that spread airflow evenly across the slot, ensuring smooth airflow from just above the...
cults3d
This is a remix of Hayden Huntley's magnetic effector for use with the Ultibots Micro Extruder. ... I also configured it to use a piece of ptfe tube as a filament guide.
thingiverse
This is a reworked version of Hayden Huntley's magnetic effector, tailored for seamless integration with the Ultibots Micro Extruder. ...Moreover, I've fine-tuned its configuration to utilize a PTFE tube as an intelligent filament guide system.
thingiverse
This section connects the XT-60 connector to the lower frame of the UltiBots K250 (or BSE). ... Print Settings Printer Brand: RepRap Printer: Kossel 250 Rafts: No Supports: No Resolution: .25mm Infill: 15%+
thingiverse
The Ultibots K250 frame now accommodates a mounted PSU thanks to this bespoke mount designed specifically for that purpose. By reducing the height of the rubber pads slightly, it successfully fits snugly into place. ...A modified version is available...
thingiverse
I received a fantastic kit from Ultibots (item 456659) that caught my attention right away! Unfortunately, I noticed some of the spools were having trouble fitting through the holder. To solve this issue, I took the initiative and designed a...
thingiverse
This Upgraded Mount Is Designed Specifically for the K250 from Ultibots. A Major Drawback with the Original Mount is Its Proclivity to Pierce and Bind to the Stand, Leaving Minimal Room for Alternative Adapters. **User Manual** Important Notice:...
thingiverse
Connecting Your Voltmeter Panel to Your Printer ------------------------------------------ Locate the designated mounting points for your UltiBot's voltage display unit. Insert and fasten all included hardware as directed. Your connector board, now...
thingiverse
2015-03-18: Update V7: redesigned for optimal cable routing and upgraded connector mounting 2014-12-18: V4 Revamp: board rotation optimizes screw clearance, re-measured dimensions ensure accurate fit Reworking my initial electronic enclosure for the...
thingiverse
I designed this filament spool holder adapter for the Ultibot K250 V-Slot printer, available on Thingiverse at http://www.thingiverse.com/thing:456659. The regular sized Hatchbox spools that came with my printer worked great, but I wanted to use...
thingiverse
This is an expanded version of the D300VS wire mount, offering a neater and cleaner setup. It should work perfectly with any V-Slot type delta printer without issue. ... Additionally, one of these mounts has been rotated 90 degrees to prevent it from...
thingiverse
Instructions This was designed specifically with the Ultibots K250 in mind, so I'm unsure if the 300 has the same 2 sets of 2020 extrusion for the bottom frame or the correct height. After careful examination, I found that I only needed to use the...
thingiverse
Zesty Nimble E3D Magnetic Effector for Ultibots K250 Delta Printer with "Berd-Air" Style Cooling. Edit: I've got my Nimbles and have one up and running, so it's verified to work. I designed it using the Nimble documentation. Also note that there...
thingiverse
These are caps specifically designed for the corners of a D300VS delta printer. Using these caps allows one to adjust tower position without disassembling the belts or carriers. The parts are sized for commonly available 5/16" carriage bolts, as the...
pinshape
This is an adjustable magball carriage with variable spacing (42mm) based on the experimental Ultibots design for the D300VS by Brad Norman found at https://github.com/UltiBots/D300VS/blob/master/Experimental/d300_carriage_v2.stl The remix allows...
thingiverse
This is a tension-adjustable V-Slot magball carriage (42mm spacing) derived from the Ultibots experimental carriage for the [D300VS](http://www.ultibots.com/) by Brad Norman found...
thingiverse
This assembly is a drop-in replacement for existing carriages on an Ultibots D300VS. The use of 750mm long MGN12 rails is recommended. A helpful resource for aligning rails when mounting them can be found at...
thingiverse
Decided to optimize storage by attaching the Pi cam mount directly to my D300VS's existing bed clip assembly.
thingiverse
I'm upgrading my XT-60 power supply panel with an RJ45 keystone module from MWU. I connected the panel to the motion control board using a short cat-6 cable and an inline keystone coupler, which was crimped together. ... It will look really sleek once I...
prusaprinters
Now a days everybody seems to have a Plus after the name. ...So add a PLUS after your stuff.Print it in 3 colors.
prusaprinters
https://www.mcmaster.com/94180a331 It should be a drop in replacement for the existing carriages on an Ultibots D300VS. I used 750mm long MGN12 rails. https://www.thingiverse.com/thing:3962350 is useful for aligning the rails when mounting them....
thingiverse
A mount for the Mosaic Palette 2 on the Ultibots D300VS delta printer is designed to work seamlessly with any delta that features a slotted extrusion at its exterior corner. This innovative setup frees up valuable desk space by allowing the filament...