ultimaker abs filament 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=1298948 Instructions Using the following options: BottomTemperature = 250 TowerSide = 20 EmbossHeight = 0.5 TowerHeight = 110 HeightIncrement = 10 machine = ultimaker temp TemperatureIncrement =...

In our city there is a very good manufacturer ABS filament.Favourable offer from this manufacturer, buy plastic in hanks 1kg.It is advantageous to 30% than to buy ABS plastic on the reels.I made a spool design for this plastic.The coil can be...

In our city there is a very good manufacturer ABS filament. Favourable offer from this manufacturer, buy plastic in hanks 1kg. It is advantageous to 30% than to buy ABS plastic on the reels. I made a spool design for this plastic. The coil can be...

The extractor hose shown in picture above can be found in amazon in the following link:https://www.amazon.com/gp/product/B0085UZKIO/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1 The Air blower can be found in the following link:...

Filament Clip für Original Ultimaker Filament.

Ultimaker 2 filament holder 19mm radius.

Filament guide for the ultimaker original with 3mm bolt holes

A filament holder for Ultimaker usable for filament rolls with smaller diameter

A simple 2.85mm filament clip that fits the standard Ultimaker spool.

I constantly use 10m, 20m filament from faberdashery.. ...I have designed a hook to fix in the side of the ultimaker, to hold these .. ...works perfectly

The Ultimaker 2 Filament Sensor detect problems with feeding filament, such as skids, filament distance and a stuck of filament. The hardware is printed and the electrically parts are standard components. Everything you need is: 2 half usb cables,...

I use the Ultimaker 2 Filament Guide (With bearing) from dirkdirk (http://www.thingiverse.com/thing:388560) on my Ultimaker. ...Based on it, I created a second filament guide that uses the same ball bearing and the wheel part from dirkdirk and can be...

This handy loose filament holder slots onto the top of your Ultimaker Original, 2, 2 Go, 2+ or 3. ...The materials can then be fed into the machine without getting tangled or caught up on anything.

This was designed for the Ultimaker 3 series but will work on an Ultimaker 2+ as well since they share the same feeder on which the guide is to be mounted. ... We welcome any suggestions you may have in regards to the improvement of this filament...

A filament guide for the UM2 to straighten the filament in the feeder Instructions Filament guide that fits under the Ultimaker 2. Print the four parts and fit them together. The nut must not be screwed to tightly to let the pulley move a bit. You...

I needed this for my Loose Filament Holder, as the filament would jump off the UM2 supplied filament guide, I needed it to be captive, and found NeonGreen's design (https://www.youmagine.com/designs/improved-filament-guide-for-ultimaker-2) which was...

A spacer designed to hold Ultimaker brand filament spools in the correct leftmost position in the Ultimaker Material Handler. Utimaker Brand spools are 55mm in thickness while the Material handler can accommodate spools up to 70mm thick. If the...

Ultimaker holder for 1kg 3mm filament. Holder is made of furniture leg 30 mm and Ideal for coil-bobbin with 30mm hole, which accommodates 1 kg of 3mm filament. ...Soft foam clamp does not allow the coil to hang out or unwind, Clamp can be adjust by...

Since I'm creating a PET pultrusion machine with an Ultimaker filament spool, I created a model of the actual spool for sizing the mechanisms and holders of my machine. The model is close to be quite accurate since the original spool has been...

Version Control V1.0 - 17/07/2017 - Original File Upload V1.1 - 18/07/2017 - Fixed incorrect merging of bodies, resulting in a faulty overhang at filament guide ring V1.2 - 18/07/2017 - Changed the rotation of Feeder2 Filament guide to lay it flat...

A Sleek design for a small/compact roll of filament which does not fit the stock filament holder. This filament holder works great with the filament i got from www.filamentenmeer.nl. Please feel free to comment for improvements or for your personal...

... spool holder here. Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: No Supports: Yes Resolution: 0.15 mm Infill: 20% Notes: Supports aren't really needed, but I did use them to make sure the rounded edge would be printed nicely.

... and test for smooth spin. Installation. Clamp each inner wheel half over the Ultimaker 2 filament guide. Clamp each outer wheel half over that. Give it a spin. Position filament. ...SLDPRT is included in case anyone wants to make it better.

-EDIT- I've taken the files to YouMagine.com since Makerbot has joined the dark side: http://www.openbeamusa.com/blog/2014/5/22/stay-classy-makerbot https://www.youmagine.com/designs/filament-cleaner-for-ultimaker It may be a good idea to lead your...

The stock filament spool brackets that come with the Ultimaker do not fit the very narrow spindle holes on the massive 5 pound PLA Filament spools from Ultimachine. Thus, I designed these minimalistic, "plug and play" replacements which work...

(This version is currently under test) V4 Base added to save material Arm1a added to move the wheel towards the base guide Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: No Supports: No Resolution: 0.4mm @ 0.1mm layer height...

... are the same with some squares cut out in sides and back to make it even lighter. More difficult to print though.Cut a piece of sponge and feed the filament through.Just a copy of my thing at http://www.thingiverse.com/thing:133353 :)

I was pretty happy with the idea to have the filament spool at the back of my ultimaker but had a lot of spools that didn't fit on the original holder. I didn't want to use any other parts so i designed a full plastic printable one for spools with a...

... If you need bearings, go to a skate shop & ask. They will prob hand you half a dozen "old" 606 bearings for free! Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: .1 Infill: 50%

A filament guide for the UM2 to straighten the filament in the feeder