ultimaker extruder 3d models
80821 3d models found related to ultimaker extruder.thingiverse
Ultimaker orginal + extruder mount for Bondtech geared extruderhttp://shop.bondtech.se/ec/extruders/ Print Settings Printer Brand: Ultimaker Printer: Ultimaker Rafts: No Supports: No Resolution: 0.2 Infill: 20%
thingiverse
This thing has moved to Youmagine: https://www.youmagine.com/designs/ultimaker-extruder-mutli-clip This gadget clips onto the Bowden cable retainer on the top of the Ultimaker extruder. It makes retractions work considerably better (discussed here:...
youmagine
This gadget clips onto the Bowden cable retainer on the top of the Ultimaker extruder. It makes retractions work considerably better (discussed here: http://groups.google.com/group/ultimaker/browse_thread/thread/7537389e8085beaf#)This is a different...
thingiverse
A handy upgrade tool for your Ultimaker extruder gearwheel. This handy grip makes it easy to extrude by hand when changing your filament, or if you want to do some pre-extrusion just before starting a print. Hope you like it! Elwin & designshop...
thingiverse
Simple skrew replacement for Ultimaker extruder Instructions This is a replacement for the ultimaker extruder filament holder. Mine had the bad attidute to loosen during long time printing, so I replace it with another one with a lock nut. I test it...
thingiverse
I am not really good at 3D-Modelling, but I did my best and created a handle for the Ultimaker Extruder-gear. It works very well and I am really happy with the result, even tough it doesn't make sense to have a handle, to be honest. But it looks...
thingiverse
When doing retraction with the Ultimaker the quick connect on the extruder allows a bit of play. This clip tries to eliminate this play. Very similar to LawrenceJohnston shim, but this one is secured with a small zip tie and tries to grap the...
thingiverse
The extruder is designed for ultimaker 2 or its clone machine. This design supports E3D V6 hotend, the hotend is completely inside the carriage and the cooling fan can be mounted on it the airflow is designed in such way that it doesn't flow onto...
thingiverse
... is not critical. There is a tremendous adjustment range. I added a section on Extruder Drive Force Measurements:http://www.vinland.com/Extruder_Drive_Force.html The long screw is 50mm. ...The shaft screw needs to be 20mm since the yoke is 18mm.
thingiverse
I finally made a re-design of the extruder assembly of a Beta Ultimaker. The design was on my mind for a long time. The advance is the bigger diameter off the "bolt" (20 mm) and a bearing as a pressure roller. Also the wheel has just straight grooves...
thingiverse
Replacement for my brocken Extruder clip which has nearly the same dimension and works perfectly till now.
thingiverse
This is the stock gear that comes on the Ultimaker Stepper motor. Modified for printing in ABS. If you are like me you have to mash your first print layer to get it to stick, which will flares out prints. I compensated by tapering the bottom. I also...
thingiverse
I recently created some gears for my Ultimaker. These spur gears are created especially for laser cutting. Prefered material is POM (delrin). They work perfectly as seen in the video: https://www.youtube.com/watch?v=AAAizfJgaWM there's nearly...
thingiverse
Put this thing between the extruder and the frame. It will dampen some of the retraction noise. ...If you put something soft under the lower support, it is even more effective.
prusaprinters
Put this thing between the extruder and the frame. It will dampen some of the retraction noise. ...If you put something soft under the lower support, it is even more effective.</p> Category: 3D Printer Accessories
thingiverse
Another Ultimaker extruder stepper motor cooling fan shroud
thingiverse
Ultimaker extruder clean tool to keep on the machine. It easily helps to detacht the extruder bolt and claen it. ... Instructions print and use
thingiverse
This is an accessory for the Ultimaker extruder update by ghagen01 rather than a derivative. It is needed if you have produced a 50materialwheel part without threading on its shaft - printed at shapeways in steel for instance, rather than machined. ...
grabcad
This a simple, easy to print, mount for the extruder on the ultimaker. It dramatically reduces the noise of the extruder, especially for retraction. The part mounts in the original mount of the extruder and the extruder then slots into the slots in...
thingiverse
... in this position, because the layer direction prevent fatigue cracking. Now the metal stiffner on the picture is not needed anymore. Print Settings Printer Brand: Ultimaker Printer: Ultimaker 3 Rafts: No Supports: Yes Resolution: 0.2 Infill: 20%
thingiverse
To additionally cool the stepper driver of your Ultimaker, you can use a 50mm fan and this laser-cutted part. Additionally, I would recommend to have a TO220 cooler attached to the stepper with heat conducting paste. ... ...
thingiverse
Vibrations of the ultimaker original extruder are transmitted to the wood structure resulting in a lot of noise especially during retractation. Different solutions have been proposed but mine has the advantage of more compacity and stability. The...
thingiverse
Now, attach the Ultimaker Direct Extruder to the top of the carriage, making sure that the PTFE tube protruding from the carriage goes snugly into the hole on the bottom of the UDE. The other two holes on the base of the UDE should line up with the...
thingiverse
It helps to clean the drive shaft after many many successful builds. Center is a M13 hole that encloses the nut. ...Its a derivative of http://www.thingiverse.com/thing:8190 http://www.youtube.com/watch?v=TGXkQ0qusIg...
thingiverse
For one 40mm fan. ... Instructions I hope that this might increase the lifetime of the steppers.
thingiverse
It is for Ultimaker 2 extruder's cable holder. ... You need Dupont 9 pin female 杜邦9pin 母座 2.54 Pin Header 單排針 也可以使用杜邦公座 請使用 petg 100% infill 填充率
thingiverse
Instructions Reused parts from original Ultimaker extruder: 1x spring 1x M3 bolt and nut that hold the spring 1x M3 bolt and nut that attach the extruder to the feeder mechanism New parts: print 1x block ultimaker 1 extruder m4 gueggelmod (use...
youmagine
Here is a Ultimaker Z-axis end-switch fine-adjuster http://www.thingiverse.com/thing:11033 for this you will need to tilt your z end-stop at an angle so that the screw from the Z-axis adjuster will hit your end-stop and not miss.Video 5 example of...