ultimate gps breakout v3 3d models

Designed this because I didn't want to have my GPS watch on my wrist during exercise. With this model, you can mount it on the handlebar for easy view and access. Made for handlebar with a diameter of 25mm but any handlebar in the close range...

I built a customized housing for my Kobo Touch e-reader, pairing it with the Bluefly Vario GPS v 1.2 module and a large battery upgrade. To secure everything in place, I used M1.6 x 8 screws sourced from Aliexpress. You can find the exact screws I...

Print a copy of the simple plate and securely attach it to the Brauniger Basic / GPS device using velcro touch fasteners to prevent loss during flights. Attach as many or as few pieces of velcro as necessary to create a strong hold on the flight...

An updated, more compact version is available here:https://www.prusaprinters.org/prints/67382-homebrew-wifibluetooth-gps-accessory-for-aux-bus-cOriginal:This is a case for a Wifi + GPS + ESP32 project used to connect to Celestron telescope mounts. No...

Remix as I wanted the GPS to be attached to spacer and not above the frame. Compatible with Naze 32 GPS Ublox 7. GPS size without box is : 17,7x17,7x4,6. Designed for TBS Source One. Will match other frame with similar spacer distance i.e.30mm. 27...

printed in pla 0.2mm height, it's a small box to shield your neo 6 gps from hobbykings hkpilot micro apm. since there wasn't one available on this site, i decided to try my hand at 3d modeling. it was my first time using a 3d program to create...

I hooked up the connections as follows: Function Line LED Colour Cable iC880a Pin POW 1 (Green) ORANGE 21 BACKHAUL PKT 2 (Blue) YELLOW 7 TX PKT 3 (Blue) GREEN 8 RX SENSOR PKT 4 (Blue) BLUE 10 RX FSK PKT 5 (Blue) PURPLE 9 RX BUF !EMPTY 6 (Blue) GREY...

This is a remix of the Avengers: Endgame Time GPS file by Jon Cleaver on MyMiniFactory, the original file can be found here: https://www.myminifactory.com/object/3d-print-avengers-time-gps-93028 This remix allows for four 3mm white LEDs to be placed...

Human: F450 Frame Specifications Supports Integration with Ardupilot and GPS/Compass Antenna Components Additionally Compatible with "F450 External LED Module Mount" Item Number 1119141 Printing Requirements: Raft Settings: Not Required for This...

This plate allows for the mounting of a GPS (or similar sized device) in the left rear of a [Shendrones Siccario](https://www.thingiverse.com/thing:4700212). The plate can be mirrored for use on the right. The plate is only 2mm thick. 9mm spacers are...

The Human Project 399 is a cutting-edge initiative that involves the integration of a state-of-the-art 10-degree mount with an Immortal T and GPS antenna mounting system. This setup is designed to provide unparalleled flexibility in terms of viewing...

A newcomer to the Ublox Neo-7M GPS family is about to emerge at HobbyKing and other retail establishments, offering an exciting alternative for enthusiasts and professionals alike. Unveiling a novel plate design that takes the existing standard plate...

This part was crafted specifically for use with the Micro Ublox M8N GPS module on a compact mini-quad battery strap, measuring approximately .6" or smaller in width. It accommodates both left-hand and right-hand mounting configurations for added...

The wirings are very very simple: pin 16 on ESP32 goes to GPS yellow wireTx pin 17 on ESP32 goes to GPS green wire Rx then black wire goes to ground red wire goes to 3.3V And that's it. You can add a small switch to put on/off the system. The usb...

here a - yes, let's say curiosity arose: the original form of the project here - is actually the impeller drive for my projectflying disc made by swimming crabI still need a field gps - i.e. ...a transmitter - beacon and then I thought - that the shape...

Instructions: Building Your Hands-Free GPS System The Hands-Free GPS is designed for 3mm carbon fiber tubes, cut to 12 inches long, which can be purchased at Amazon.com. Alternatively, you can use 1/8 inch bamboo skewers from the grocery store or...

A mount for attaching a TBS Immortal-T antenna and a GPS module to a Catalyst Machine Works Shocker. I have the 4" ultralight version but I think this should work with all sizes. Design is not perfect as it sits a bit low and touches the floor...

This old Garmin eTrex handheld GPS is great for tracking distance hiked or biked, but its handlebar mount has been lost. To replace it, I designed a new bracket with overhanging tabs and filleted underside to ensure proper fit. Print the bracket and...

I'm excited to share with you a custom holder for your GPS unit, designed to resemble the DJI naza's module. You can find the design file here: http://goo.gl/pqBJc6. If you'd like to adjust the diameter of the hole where the shaft fits, I've included...

Thus, I designed a GPS handlebar mount for my Ducati 848. This is the initial prototype, and constructive feedback is more than welcome. The components were printed in PETG with 100% infill, making them slightly flexible during installation. In...

... at http://wiki.paparazziuav.org/wiki/Main_Page for a smooth operating experience. Most recently, I've integrated a GPS mount into its sturdy framework, complete with an understudy support structure which only requires simple removal to take flight.

I required a compact, lightweight pedestal mount for my M8N GPS sensor on a 250 quadrotor. This accommodates a straightforward 15mm hole in the frame. Secure the quadcopter frame between the bottom of the tower base and the disc clamp using one...

A GPS case is available for the 20-Channel EM-406A SiRF III Receiver (sparkfun.com/products/465) featuring an antenna. The case incorporates mounting holes suitable for 4-40 screws and a frontal port for cable access. Additionally, it has a top hole...

I wanted to simply put it under the original GPS mount and be done with it. But the original one was able to bend down and touch the Rx. Plus the gap was a tad to narrow for my liking. I designed this one to easily accommodate the Rx and keep the...

If you have a smaller GPS or want a tighter fit, just heat the middle over the stove and bend the hooks a few mm closer together. Feel free to hit that "Tip Designer" button - I dropped my laptop a couple days ago and it's my main design tool. It's...

Modular (bicycle) mount for older Garmin eTrex GPS receivers (and everything else you want to attach). Basically this is my design idea for a mounting system that I've specialized for my old Garmin eTrex Legend HCx. The goal was a modular system...

I wanted a mount that was able to mount not just a GPS and not rely on double sided tape. This GPS mount/shelf is positioned 20mm back from the front edge of the motor hump and is 30mm long. There are also 4 mounting holes that could be used to mount...

This is a remix of the Avengers: Endgame Time GPS file by Jon Cleaver on MyMiniFactory, where the original file can be found at https://www.myminifactory.com/object/3d-print-avengers-time-gps-93028. The remix allows for four 3mm white LEDs to be...

3) Version for Aluminum GoPro Out Front Mount - This combo mount combines the functionality of a Lezyne GPS mount with an aluminum GoPro attachment, allowing users to attach both devices to their handlebars. To create these mounts, simply print the...

Tripple SMA + Beitan BN-220 GPS + optional: external Barometer ("BOSCH BMP280") Made for F/7 V6, will fit V5. ... Frame: https://www.cncdrones.com/FR7-v6-Frame_p_18.html Baro:...