unity 3d city builder

Use one finger to hold the stand and your other to press down on the horizontal linkage. Note: Adding magnets or some form of weight to the the horizontal/vertical linkage connecting point will help smooth the operation of the...

The power consumption is very low (12v 0.09amp for 1.08w) and the fan is very quiet if you use the same as mine. For this project you will need :4x M3 threaded inserts (max 6.5mm deep)4x M3 screws with a length of about 7-8mm4x M2 threaded inserts...

(I wondered if I had connected it properly, I had :P ) Ender 5 test 2: Removed the 2nd 120 mm fan extracting and kept only my regular inlet fan, still running at 6.5 volt Again, I kept the original fan connected. During this test, once again, the fan...

We've found a Drawer_Gap of 1.0 (mm) to be sufficient, but results will vary for different 3D printers. If unsure, you can test the gap by printing a drawer of your chosen dimensions and a chest for a single drawer (Drawers_Across set to 1 and...

https://www.youtube.com/watch?v=5Y1Psf6igHE Step by Step instructions: https://www.instructables.com/id/Juuke-a-RFID-Music-Player-for-Elderly-and-Kids GitHub: https://github.com/ananords/Juuke ••• Parts: ••• Arduino UNO...

First of all, I improved the thread which attaches to the drink bottle as I felt that Gavin's was a wee bit messy when it came to 3D printing - one or two strands of plastic which I had to remove before attaching the bottle. The main job though was...

Project Details: https://aed.contact/en/parametric-pencil-box/Proje Detayları (Turkish): https://aed.contact/parametric-pencil-box/REQUIRED MATERIAL LISTNo.Product NamePieceLinkNotes13D Printing (2 pieces)1* 2Screw3  

... original dehydrator lid, I decided to carve four exhaust slots of 1/4”x 1” each around the edge where the walls curve into the lid. Now I am seeing a clear improvement when drying PLA and PETG.    Category: 3D Printer Accessories

... that they call HT (basically tritan) and is supposed to withstand temps over 100°C. Category: 3D Printer Accessories

I will lock away the goodies in the drawer, then lock the key to said drawer into the piece of 3d-printed plastic inside a padlock. The key to the padlock can then be put in a place that is not too close by, or easily reachable. Maybe hide the key...

Non-3D printed parts: Four 10-24 machine screws (2" or 1.5" long) (10-32 or M5 should also work) Eight 10-24 nuts (10-32 or M5 should also work) Four 13" zip ties 1/16" self adhesive cork (use thicker if your tube diameter is smaller) Four 10-24...

 You only need the left or right versions (plus the others) so the whole thing should print in about 2H 54m or so.The 3mf files are ready to print with appropriate supports and brim.There files, suitably named, for right and left handed...

... what I can do.</p> <p>BTW... I am currently designing a top enclosure with hinged lid... that will definitely not work with steppers hanging off the rear and inverted (IMO a clumsy non-compact design). Teaser coming soon. Category: 3D Printer Parts

For reference, the translucent PLA colors I used were: Red - https://ultimachine.com/content/pla-175mm-red-translucent-1kg-spool Green - https://ultimachine.com/content/pla-175mm-green-translucent-1kg-spool Blue -...

 I have made two of these using PETG with carbon fiber filled PETG handles and they have easily lasted the past three years of use. If you sufficiently enjoyed and made use of the free 3D models and files I have provided, please consider buying me a...

You'll need to print: - 1x Main Body (or, if you'd like to have shorter print times and an easier time with electronics 1x Main Body Split Handle, 1x Main Body Split Front) - 1x Handle Cover - 1x Bridge - 3x Body Pin - 1x Barrel - 1x Shell Front -...

Obviously this is one of the ever-growing number of problems in life that can only be solved with 3d-printing. My goals: 1: Design a squeezer for ~1/2l of juice 2: Make it motorized because why not? 3: Use a graceful way to activate the motor 4:...

... <p>Hopefully this all makes sense &amp; I have included everything required.</p> <p>Thanks for looking.</p> <p>p.s. wise to perform a new bed level after fitting this mod &amp; running the 'Align Z Axis' option. Category: 3D Printer Parts

This is my attempt to try and recreate the Cristelia 3D printer, which unfortunately seems to have been abandoned. Things I have changed so far: The corners are now made to use 1in tubing that can be found easily in most American hardware stores. I...

Then I used OpenSCAD to create the final 3D model from dimensions and polylines I derived from DraftSight. This part could probably be used for other Kossel 2020 Deltas, but it was created to be used with the Folger Tech Kossel 2020. There's a test...

... probably all you could easy change by editing GCODE, any more just start from scratch. Print Settings Rafts: No Supports: No Notes: Edit GCODE for yoiur printer if on 300mm x300mm bed I used ABS 110 bed and 240 hotend Category: 3D Printing Tests

These settings were optimized using Simplify 3D and work well with PLA/PETG filaments (may require adjusting nozzle temperature for PETG).\r\n____\r\n\r\nMASK UPDATE 1.2\r\nA new design will be shipped out this...

... more durable filaments like ABS, PETG, Nylon, etc...I printed this, as modeled with supports at a density of 5%. I used an infill density of 33% using Cura's "Zig Zag" pattern to support the weight of a 1kg spool.  Category: 3D Printer Accessories

Hopefully you're here because you've heard about Mutant, an exciting new product to enhance your 3D printer. If you have Mutant then you'll need ways of attaching your favourite hardware to the multiple mobile plates, so here are a selection of...

This is based off the 3DLS Complete Belt-Free 3D Printer #First print I run SKR 1.4 on my machine and this is not possible with the stock control board. What you will gain is much improved Y axis performance at the cost of a little noise due to the...

If you are doing repairs on electronic devices or assembling small machines like 3D printers, this could come in handy.I used this one, but just about any 22mm nato strap should...

Subscribe to find out more support free 4K Time-lapse video: Subscribe Now! youtube.com/watch?v=0m4EnaPzadk&list=PLiilF_5yk3dPSMlEYUnDXscJI6oKquxvo https://youtu.be/uNqqN5Ao_hI https://youtu.be/-ZsXFX6hjXk https://youtu.be/3zdRgYUHfvU ...

Vector 3D has a good video on Youtube that explains the proper use of drag chains.Finally, I've included a new version of the cable organizer (Face Plate.stl) should you decide to use it. The new design does not require a JST connector on both...

I made this model mixing the stereographic model from the south face of Arrokoth from the supplementary material of Spencer (2020) and the shape model from Stern (2019) published in the 3D Asteroid catalogue, using MATLAB R2016a. The New Horizons...

=&gt; Discarded Side View of Iteration 1 - notice that the measurements here are off by 0.4mm in Z and XZ! Itteration 2: Avoiding the M4 screw head on the other side seemed like a better idea, yet still the measurements were off Iteration 3 -...