usb port cover 3d models
202303 3d models found related to usb port cover.thingiverse
USB Port cutting cover This file is a simple USB cover for USB rectangle cutting.
prusaprinters
USB port cover for any USB-A port.Useful for:Covering up a damaged port so it's no longer used.Protect unused ports from dust.Childproof device ports.VERY fast print with no support required. Make sure your printer is tuned as dimensions are fairly...
thingiverse
Simple plug to cover dual USB port, if unused. ...Print Settings Rafts: No Supports: No ...
myminifactory
This is a cover for the USB ports of PCs, power supplies, power banks and a lot more. ...Its purpose is to prevent dust and dirt to go into the port when you aren't using that.
cults3d
This is a cover for the USB ports of PCs, power bricks, power banks, and a lot more. ...Its purpose is to prevent dust and dirt to go into the port when you aren't using that.
thingiverse
I created this little cover for using it in a seagate NAS that has an USB port never used and prevent moisture to get into it. I post it because it maight be usefull for someone else... ... Cheers!
prusaprinters
This is a cover for the USB ports of PCs, power bricks, power banks, and a lot more. ...Its purpose is to prevent dust and dirt to go into the port when you aren't using that. 3D printing settings:You can print this file with a 0.1mm to 0.2mm layer...
thingiverse
I created these to keep dust and stuff from fouling up the unused USB ports on my devices. ...They worked quite nicely on the majority of the USB ports which I tested them on except for a few which were a tad loose/tight.
thingiverse
... ...Printing takes only about 20 minutes. Use raft for better stability. USB male connector may slightly vary in size due to manufacturing tolerances (around 0,1mm). If the cover doesn’t fit properly, resize by 1-3% in slicing software. ...Enjoy...
thingiverse
I needed a "dust cover" for a USB port that failed on a 5-port charger. I was always forgetting which port was bad... and then I'd wake up and some device hadn't charged all night. I put an X on the bottom/part facing out so that people think before...
thingiverse
A protection cover for my custom USB port on Sigmarion II Handheld PC (Windows CE H/PC 2000).
thingiverse
These little guys cover up your unused USB ports to keep dust and junk out of them. Are they needed? No. But they look great with my Pi case. (https://www.thingiverse.com/thing:2391969) I just wanted to cover up the unused ports on my Octopi setup. I...
prusaprinters
These little guys cover up your unused USB ports to keep dust and junk out of them. Are they needed? No. But they look great with my Pi case. (https://www.thingiverse.com/thing:2391969) I just wanted to cover up the unused ports on my Octopi setup. I...
thingiverse
Just made this cover super quick as I could not find any. Printed in TPU. No support needed if printed very slowly. ...
thingiverse
... console. Note, the USB Port Cover is Directional. Print in TPU if possible or PETG as PLA will melt inside the car. Check fit and apply shims/electrical tape or add thickness to the part for better fit. ... IPT is attached for modification.
prusaprinters
Covers for USB type A, USB type B and USB-C Print instructionsSet perimeter to 3. The USB-C cover requires thin wall detection to be activated in PrusaSlicer if printing with 0.4 nozzle. ...3mm brim is also recommended.</p>
thingiverse
I print it in white PLA so it make contrast with the black metal box and the balck sd, so it's much more easy to put the sd in the port and without fear. May be the peace need some minimum accomodation to fit perfectly with your metal box and...
cults3d
... Hubsan Zino has the Micro SD/USB port exposed to the elements, there is potential for dirt and dust to get in. ...I made a port cover that attaches by using the mirco USB port. ...I have tested it in flight and it did not come off; its secured well.
thingiverse
... Hubsan Zino has the Micro SD/USB port exposed to the elements, there is potential for dirt and dust to get in. ...I made a port cover that attaches by using the mirco USB port. ...I have tested it in flight and it did not come off; its secured well.
thingiverse
To install, slide the cover under the front lower horizontal frame bar, between it and the horizontal piece of acrylic plastic below, and to the right of the USB ports, with the notch on the cover facing front and down, then slide the cover to the...
thingiverse
TPU printing with 80% infill. ... Two versions (thicker and thinner) - on the photos show a version with thinner walls
thingiverse
... from snapping off and getting stuck in the port. The side that sits flush with the case was based on the original design by newdaynow (https://www.thingiverse.com/thing:1154670) and chopped off and resized to serve as a base for my USB port tab.
thingiverse
I designed my own Cover for the RetroSix Clean Power Mod which fits perfectly for me. I printed it with PETG which helps a lot while installing this and does not get damaged. ... Thanks to RetroSix, The CleanPower GG is an awesome Mod !!!