valve guide removal tool 3d models

My laser cutter came without a tool to remove the lens, so I made my own. For C and E series laser heads with a 20mm lens.Add a 25x2.1mm nail without the head using a soldering iron. ...The nails I used were left over from an IKEA PAX cupboard,...

Update 04.09.2021: Added v3 [also works with NLR EVO (see here: https://youtu.be/VGiIuhoHvEE or here: https://lbre.de/hp/nlr_evo.html)] Update 10.08.2021: Added v2 (has protection from closing too far) I really like the Rekon3 / NanoLongRange from...

... design up here just in case it somehow finds a use. A tool designed to remove headset cups from an older bike with a 1-inch threaded fork is what this is all about. ... Similar to this existing design: https://www.youtube.com/watch?v=VkY879pMafE

tired of messing around with the slotted ring to remove the laser lens for cleaning, this tool should help for the smaller laser head. note - added 20mm id to downloads after 100% fill, i still had tab break, my laser ring may be too tight ...

... could easily be reduced to thinner cross-sections and minimal infill without sacrificing functionality. In fact, I would estimate that this tool is roughly 1cm taller than it needs to be for a precise fit and successful removal of the retainer ring.

I encountered a critical problem with the telescope after two months of frequent use and removal (72 degrees to approximately 10 degrees), where the 68mm recessed T-thread adapter became severely stuck in my Moonlite CHL Focuser drawtube. I...

Thanks to Luberry for the original 24mm Snap button removal tool, this remix is for Sanwa OBSF-30 30mm pushbuttons. I've also included the corner cut out for the joystick panel mounts and I attached the f3d file as well. I was pretty impressed by...

I made this La Pavoni Boiler Nut Removal Tool - for the Premillenium La Pavoni Versions (1986) because the other one available here was not really fitting for me. [as reference: this one did not fit for me: https://www.thingiverse.com/thing:3877491...

This is a tool designed to remove the gas tank cover ring on a 2003 Volvo XC70, potentially effective for other models but untested. The center hole accommodates a 2x2 inch piece of dimensional lumber precisely. I've uploaded the Autodesk Fusion 360...

I thought that printing a tool would engage all of the retention clips, so I was glad to find Davidhbrown's design on Thingiverse. Unfortunately, it needed to be printed vertically, and I had trouble with layer adhesion. I reused some of...

This tool is designed specifically for removing the roll pin that secures the ejector pin in an AR-10/LR-308 bolt. For reference, a similar design can be found at https://www.thingiverse.com/thing:3270414, which offers an AR-15 remix courtesy of...

A simple tool to help aid in the removal of the PSU switch on the Creality Ender 3 (Pro). To use it, place the notched end around the PSU switch and press firmly to depress the tabs on the switch. You should then be able to push the switch out. I...

... all Seiko watch models, but it worked like a charm on my 7T32- model. To remove the back of your case, simply align the nobs on the tool with the notches in the back and turn counter-clockwise to loosen, then clockwise to tighten when you're done.

This does the job of part #1810031, which is a $60 USD tool for removing the rocky mountain shock hardware from the shock. I only know that this works on the mountings for a 2019 altitude alloy with a dpx2 shock, as i made this for my own needs. ...

I modeled a tool that would allow me to easily unscrew the tank from the body. Note that the tank only needs to be unscrewed about 30 degrees for it to be removed. If the tank does not drop out after turning, try rotating back and forth a small...

sensor soap dispenser to attempt a repair but had no easy way of removing the lower tank/reservoir that holds the soap. I modeled a tool that would allow me to easily unscrew the tank from the body. Note that the tank only needs to be unscrewed...

Simple device for removing the rear cap of Emek/Etha 2 markers.

If you own a newer Rocky Mountain full suspension bike, you'll know the bearing eyelets on the rear shock are a pain in the ass to remove for replacement or to perform an air can service. The official Rocky Mountain tool is $$ and frequently out of...

I needed an opening tool for my oven lamp cover to change the bulb. ...So I designed this simple unscrew helper tool. Suitable for many oven types with Ø42mm lamp cover. ...Tool sizes in PDF drawing…

If you own a newer Rocky Mountain full suspension bike, you'll know the bearing eyelets on the rear shock are a pain in the ass to remove for replacement or to perform an air can service. The official Rocky Mountain tool is $$ and frequently out of...

Thanks to Luberry for the original 24mm Snap button removal tool, this remix is for Sanwa OBSF-30 30mm pushbuttons. I've also included the corner cut out for the joystick panel mounts and I attached the f3d file as well.</p> <p>I was pretty impressed...

If you own a newer Rocky Mountain full suspension bike, you'll know the bearing eyelets on the rear shock are a pain in the ass to remove for replacement or to perform an air can service. The official Rocky Mountain tool is $$ and frequently out of...

I created a proof-of-concept replacement part for a Fiskars weed removal tool. The lower section was damaged and I replaced it with a 3D-printed version. Unfortunately, it cracked after only a few uses. Perhaps printing it with ABS would have...

If you have a different quick release line, you can probably just resize this tool to fit. The engine shown is an ISL 9 model. To print this tool, use a strong flexible plastic like PETG or Nylon. ...Printing with 100% infill and larger layer lines will...

Increased wall thickness ensures the tool's durability during twisting, simplifying printing process. ...Support isn't necessary and a 100% fill is suggested for optimal results.

Removing the Heating Element on Old Brass Style La Pavoni Espresso Machines To take out the heating element on an outdated brass-style La Pavoni espresso machine, you can use a wrench extension and turn it with a ratchet.

Cage Nut Insertion Tool for Easy Server Rack Management Insert cage nuts quickly and efficiently into 19-inch server racks or cabinets with this specialized tool, designed to streamline your data center operations. Simply add an M4 screw and two M4...

... 4th year dissertation on the improvement of this tool. ...No model existed and i roughly produced this using a picture of the tool with a ruler in the image and took dimensions from the image by setting my screen to the same size as a physical ruler.

... get the nozzle off if it's being stubborn. Getting your fingers in the shield can be tricky on the 10w D1 so I made this tool to help. Makes taking the nozzle off a breeze. ... Video on the website http://viperdesigned.com/laser/xtool/D1/D1VA2/

I am removing snails, snail eggs and roes of corydoras which are sticked to glass. All with dry hands.This way you can easily control population of snails or simply move roes to secondary spawn tank to protect roes from being eaten by other...