volcano hot end 3d models
171903 3d models found related to volcano hot end.thingiverse
Airwolf HDx2 Volcano hot end change, **Project Resurrect POS AIRWOLF** This is an attempt to upgrade an Aging (and never good POS HDx2), This is a project and I'll post more as it goes on. may be long term. Replacing the original carriage to swap...
thingiverse
Based off of Hot End pen holder by nils_kal Converted to resemble the Artillery SWX1 & Genius Titan /Volcano setup found on stock printer. ...Slightly skewed scale to allow for it to stand properly and provide storage for larger pens and markers.
prusaprinters
Based off of Hot End pen holder by nils_kal Converted to resemble the Artillery SWX1 & Genius Titan /Volcano setup found on stock printer. ...Slightly skewed scale to allow for it to stand properly and provide storage for larger pens and...
thingiverse
For mount Volcano v6 just need modificate the mount of bltouch to raise up ( sharp knife) and print these for fans
thingiverse
Crude modification to accommodate for the E3D Volcano hot end and my openbuilds v-slot mini-gantry bracket. Print Settings Printer Brand: RepRap ...
thingiverse
Got a Creasee Skywalker, broke the tip, but had a V6 Volcano hot end and an extra Heat break, great excuse to upgrade a little. Couldn't use the heatsink from the V6 though, eh. Needed a new fan duct. Couldn't find one similar to the old one, so i...
thingiverse
Sidewinder X1 with .6mm nozzle and volcano hotend needs larger Temperature tower to test PLA so trying this one.
thingiverse
This is a single component to provide the x axis assembly incorporating a volcano head with a bowden setup with hotend cooling fan, as well as two centrifugal blowers for print cooling. ... The video may make it easier to understand.
thingiverse
Customized version of https://www.thingiverse.com/thing:1141659 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1141659
thingiverse
Adds an extra 7mm to the auto levelling switch,for use with the Volcano hot end. Can be printed in any material you like, but ideally ABS or PETG. ... No firmware changes needed
thingiverse
I have recently converted my Creality CR10S to a Titan Aero direct drive extruder with a Volcano hot end and prior to the conversion I was using a BLTouch bed leveling sensor. There are several mounts here on Thingiverse but nothing that really fit...
cults3d
I have recently converted my Creality CR10S to a Titan Aero direct drive extruder with a Volcano hot end and prior to the conversion I was using a BLTouch bed leveling sensor. There are several mounts here on Thingiverse but nothing that really fit...
thingiverse
Hot End Fan Duct: Works for E3D V6 Heatsink or Clone. Can be used with 40mm fan directly and you don't need the original E3D 30mm fan duct to put on an adapter. I printed it face down with simple touching build-late support and maybe support is not...
thingiverse
Customized version of https://www.thingiverse.com/thing:1141659 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1141659
thingiverse
I used the small minimalist mount for my V6 and needed a part cooling fan mount. This is modified from something I found here on Thingi, sorry don't remember which one. You'll need a 5015 fan. ... Works on CR-10S, Ender 2, Ender 3 etc.
thingiverse
Extended hotend mount for volcano heater block
prusaprinters
Extended hotend mount for volcano heater block Category: 3D Printer Parts
thingiverse
... adjustable-position duct that attaches to a very solid base bolted to the aluminum. After about twenty or so revisions and tests this is what I ended up with. ...It all would have been 100x harder to do without the original 40mm and 50mm brackets.
thingiverse
I've also included a riser plate to allow the attachment of a Volcano hot end. Both options continue to allow the use of the printer's standard calibration hardware and as a bonus the original mount for a rather weak 40mm blower has been...
thingiverse
This really shows the narrow directional airflow with low pressure air exhausting the “used” hot air to the back of the build plate. This provides a constant fresh airflow on the filament. It also shows why I suggest you mount your duct outflow ports...
thingiverse
Customized version of http://www.thingiverse.com/thing:1141659 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1141659
thingiverse
Modded to get work in Volcano hot end.
thingiverse
This new and revised strengthened vent to work E3de V6 Volcano hot end FLSUN QQ-S
thingiverse
Same as Fan_ductv3.3 but made taller for the Volcano hot end.
thingiverse
Another BLtouch mount for the vergienc hotend assembly. ...Suitable for Volcano hot ends. ...
thingiverse
Just a very basic remix to make the original design's fan shrouds work with a volcano hot end
thingiverse
A quick and dirty remix of vampyrex13 bltouch mount to accommodate for the extra length of a volcano hot end
thingiverse
i have created this fans so i can have both distance of the magnet and right fan ducts for volcano hot end
thingiverse
I designed for volcano hot end the shroud - I have not yet printed it I will update this once I have printed it added 10mm extra height version.
thingiverse
Stretched the fan duct, and heatsink cooling fan parts to fit the e3d V6 Volcano hot end. everything else should be the same. ... STL and STEP/F360 files for the standard afterburner: https://github.com/VoronDesign/Voron-Afterburner