vortex crossfire ii 1 4x24 throw lever 3d models

Throw lever for Primary Arms 1-6x SFP scopes. This is an original design. **TABLE OF CONTENTS** - Parts - Printing Details **PARTS** - (1) M3x12mm socket head screw - (1) M3 nut **PRINTING DETAILS** - Settings (Tested on ender 3V2 with 0.6mm...

Re-mix from the throw lever by jitblass. I fixed the messed up geometry, beveled the edges (so you don't have to sand them afterwards), and shrunk the cutout for the nut to accept standard M3 nuts. Once printed, you'll need a M3 x 10 screw and...

The Cat Tail Lever attachment is designed to complement the Optisan Mamba 1-4x scope, which had a limited release a couple of years back. ...This custom component was 3D printed without any support structures.

Requires 1 M3 nut and 1 M3*8 cup head screw Printed with resin and FDM, both works great

... with a 3/8 inch hex nut to generate the necessary tension. ...The chosen screw should be exactly 7/8 inches in length; one option is to employ a longer screw, such as one that measures 1 inch in length, and then trim it down to meet specifications.

One this I did in Cura was set the screw in portion of the lever and the lever itself to 100% infill and the rest (The ring) at 40%. The reason I did 100% was so the threaded inserts had more plastic to grab onto. Materials needed: 1. Strong...

Thumb Throw for a Vortex Viper 44mm dial

Throw lever for original Strike Eagle 1-6. Design uses just a M3 screw directly into the plastic. ...I used PETG for the durability and ease of getting around the 30mm tube but PLA will work too.

Throw lever designed for the Barska Euro-30 4A 1.25-4.5x LPVO. ... Hardware needed: Any screw and nut that fits

Throw the lever for Meopta's K-Dot 1-4 and its variation, the Meostar R1. It works seamlessly, having been put to use for an extended period in cold temperatures without malfunctioning. ...A crucial requirement for this setup is a M3 machine bolt and...

This is a remix I did of two Scope Throw Levers on Thingiverse. It was designed to fit the Primary Arms ACSS Raptor 1-6 FFP Scope perfectly without any scaling required, even when printing with ABS material. I printed the part at 100% infill and...

No supports needed for anything but you can use it on the lever for the screw and nut holes. Just snug tight, no need to crank on it. I printed the lever at 100% infill with carbon fiber petg. It's strong and matte black. The TPU was 20-30% no...

To fine-tune the positioning, align the component so that the throw ranges from approximately 10 to 2 o'clock. Next, slip the M3 nut onto the 10mm threaded rod and secure it by tightening until snugly in place. ...The hardware specification includes: M3...

Simple dust cover/lens caps with eyelets for the Vortex Crossfire. ID could be expanded another 0.2mm but these fit nice and snug. ...

Insert the nut into the cavity of the Scope Throw Lever for Vortex Viper PST Gen I, then grind off any excess material with a precision tool. ...Next, cut the M2.5 screw to the precise length required using a high-quality cutting instrument.

A cover for the Vortex Crossfire red dot, no more fugly front mounted bb shields ;) You need to cut some polycarbonate sheet (or safety goggles ;) ) into the size of the cover and a M3 screw and nut to screw it on the red dot.

Simple throw lever fo visionking 1.25-5x26 scope. Fix file is an element that is used to fill a small gap in the lever. ...You need a m3 screw for this.

Throw Lever and Parallax spinner for the Kahles K525i Scope The throw lever has an offset knob to clear the hand and bolt when at minimum maginification. It can be reversed for left handed shooters for when at maximum magnification. Both the throw...

A simple and robust throw lever designed for 44mm.This model requires a 20mm M4 Bolt and nut.

The new VX6 HD's come with a throw lever but anyone stuck with a first gen is also stuck paying over $100 for a throw lever. Both iterations worked great. I prefer the V4 for use but the large lever irritates me sometimes. Might switch back to V3...

Print on the side, fine detail, at least 3 perimeters. ...Can be used on Nightforce scopes instead of the 65$ throw lever that they offer. M2x16 to tighten if tapping into plastic is enough. Feels good enough. ...Can also do with M2x20 and nut.

scope throw lever for Leupold Rifleman 3-9x40 designed to fit over a 36.2mm adjuster. I used a M3x8mm bolt, but you could probably use a 5mm I added two M3 washers in the gap to prevent over tightening the ring two edges would not take a...

To do my own throw lever I used "Primary Arms 4-14x FFP Scope (1st gen)" from PoniesWhee because its quite minimalistic and I like how it look. I made some changes inside the lever to fit ring correctly, and also change a little scale to keep it...

You can customize everything from the length of the throw lever, to the position of the clamp to the angle and depth of the scope notch. Best part is all you need to do is install Fusion360 and figure out how to load the step file. (not rocket...

Wraith Scope Throwing Mechanism Activated

I Designed a VX6 Throw Lever That Works Perfectly. Anyone with an Older VX6 HD Model Is Still Stuck Paying Over $100 for a Basic Accessory. Both My First-Gen and Newer Models Worked Flawlessly, But I Prefer the V4 for Its Smooth Performance - The...

To create my own throw lever, I drew inspiration from the Primary Arms 4-14x FFP Scope (1st gen) by PoniesWhee, which boasts a sleek and minimalist design that I really like. Inside the lever, I made some adjustments to ensure it fits snugly with...

You can customize various aspects of the throw lever design, including its length, clamp position, scope notch angle, and depth. The best part is that all you need to do is install Fusion360 and figure out how to load the step file - not rocket...

This is a scope ring lever for the Monstrum G3 1-3x24 FFP scope. ... It is deliberately a very tight fit, and will require patience and mechanical persuasion to install.

The Vortex Optics Viper PST 6-24 scope features a robust design and exceptional optical quality, making it an ideal choice for long-range shooting applications. ...On March 29, 2017, the addition of a detailed SketchUp model further enhances its appeal...